Well....I'm back....
#1
Supreme Member
Thread Starter
iTrader: (3)
Join Date: Sep 2016
Location: Sunny Florida
Posts: 1,813
Received 223 Likes
on
149 Posts
Car: 87 Trans Am
Engine: 5.0
Well....I'm back....
Hey guys, after stepping away for a few months I'm back.....as you knew I would be
I bought back one of my old cars.....some things will never change....
I bought back one of my old cars.....some things will never change....
Last edited by BizJetTech; 11-11-2020 at 03:53 PM.
The following 5 users liked this post by BizJetTech:
chazman (11-11-2020), DynoDave43 (11-14-2020), liftem (02-27-2022), rt66er (11-11-2020), TTOP350 (11-12-2020)
#2
COTM Editor
iTrader: (22)
Join Date: Mar 2001
Posts: 9,910
Likes: 0
Received 1,857 Likes
on
1,272 Posts
Car: '89 Firebird
Engine: 7.0L
Transmission: T56
Re: Well....I'm back....
Very nice choice!
The following users liked this post:
BizJetTech (11-11-2020)
#6
Supreme Member
iTrader: (2)
Join Date: Mar 2014
Location: South Ms
Posts: 4,429
Received 722 Likes
on
491 Posts
Car: 89 Firebird
Engine: 355 TBI
Transmission: 700R4
Axle/Gears: 10 Bolt.Posi-3.73s
Re: Well....I'm back....
Those Crosslace wheels looked great on that car, you gona put em back on? I agree with Shifty id leave it stock but id run the Crosslace wheels and save the stockers. Gorgeous car and good to see you back
The following users liked this post:
liftem (02-27-2022)
Trending Topics
#8
Supreme Member
Thread Starter
iTrader: (3)
Join Date: Sep 2016
Location: Sunny Florida
Posts: 1,813
Received 223 Likes
on
149 Posts
Car: 87 Trans Am
Engine: 5.0
Re: Well....I'm back....
Yes, will most likely put the crosslace back on it.....but also considering these....https://www.hawksmotorsports.com/82-...-reproduction/
#9
Supreme Member
iTrader: (5)
Join Date: Oct 2002
Location: In the paint booth!
Posts: 2,659
Received 1,161 Likes
on
654 Posts
Car: 1986 Camaro Drag Car
Engine: 383 on Ethanol
Transmission: Automatic
Axle/Gears: 3.90 Currie 9 inch
Re: Well....I'm back....
Congrats man!!! Great car! I loved it with the crosslace wheels, too!
The following users liked this post:
BizJetTech (11-12-2020)
#12
Supreme Member
iTrader: (1)
Join Date: Mar 2016
Location: New England
Posts: 2,406
Received 190 Likes
on
128 Posts
Car: 1988 IROC Z Convertible
Engine: 305 TPI (LB9)
Transmission: 700 R4
Axle/Gears: G80 GU2
Re: Well....I'm back....
That was a great RS!
good luck getting those Ronal wheels! They’ve been out of stock for a while, but IMO on the non IROC cars they are the best looking wheels.
good luck getting those Ronal wheels! They’ve been out of stock for a while, but IMO on the non IROC cars they are the best looking wheels.
The following users liked this post:
BizJetTech (11-12-2020)
#14
Supreme Member
Thread Starter
iTrader: (3)
Join Date: Sep 2016
Location: Sunny Florida
Posts: 1,813
Received 223 Likes
on
149 Posts
Car: 87 Trans Am
Engine: 5.0
Re: Well....I'm back....
up a set of repo's here or on ebay.....that is IF....I decide to go with them, I'm leaning towards the GTA cross lace again
#15
Supreme Member
Join Date: May 2015
Location: Florida
Posts: 1,709
Received 239 Likes
on
185 Posts
Car: 1991 Z28
Engine: 305 TPI
Transmission: 700R4
Axle/Gears: 3:42 Auburn
Re: Well....I'm back....
Welcome back Kotter...I mean Biz.
Wasn't your original plan for this car to swap the engine or performance it up? Crosslace wheels and HP, can't go wrong there.
Wasn't your original plan for this car to swap the engine or performance it up? Crosslace wheels and HP, can't go wrong there.
Thread
Thread Starter
Forum
Replies
Last Post