attention IROCET
Thread Starter
Member
Joined: Feb 2001
Posts: 314
Likes: 0
From: Mesquite, Texas
Car: 1992 Chevrolet RS Camaro
Engine: 305 TBI
Transmission: WC T5 conversion
Axle/Gears: Debatable . . .
attention IROCET
Sorry Irocet.......I have no idea why I typed your name lol.
Try this website they have a box for (3-4) 8" subs or (2-3) 10" subs.
http://www.autoboxx.com/secondpage.html
This site has several dual sub boxes but they also have a quad sub setup.
http://www.tune-town.com/Installatio.../Camaro_TA.asp
------------------
1988 Camaro
305 bored .030 over
Stock TBI
Aluminum radiator
No smog pump
gutted factor cleaner
cam ground to crane specs
timing advanced 9 degrees
no thermostat
other than that its bone stock and ran a 16.4 @ 82 mph with earth shattering wheel hop and a 2.88 60 ft time. (this was with the rebuild and cam only)
[This message has been edited by racer J (edited March 02, 2001).]
[This message has been edited by racer J (edited March 02, 2001).]
Try this website they have a box for (3-4) 8" subs or (2-3) 10" subs.
http://www.autoboxx.com/secondpage.html
This site has several dual sub boxes but they also have a quad sub setup.
http://www.tune-town.com/Installatio.../Camaro_TA.asp
------------------
1988 Camaro
305 bored .030 over
Stock TBI
Aluminum radiator
No smog pump
gutted factor cleaner
cam ground to crane specs
timing advanced 9 degrees
no thermostat
other than that its bone stock and ran a 16.4 @ 82 mph with earth shattering wheel hop and a 2.88 60 ft time. (this was with the rebuild and cam only)
[This message has been edited by racer J (edited March 02, 2001).]
[This message has been edited by racer J (edited March 02, 2001).]
Member
Joined: Nov 2000
Posts: 216
Likes: 0
From: San Jose, CA
racer J,
Thanks for the links. I'm trying to stay away from the "one box fits all". I liked the JL box because it was "pre-fab" for third-gens but specific and chambered for the 3 10W6's. I suppose I could just build one myself and it may be the way I'll end up going.
Matt
Thanks for the links. I'm trying to stay away from the "one box fits all". I liked the JL box because it was "pre-fab" for third-gens but specific and chambered for the 3 10W6's. I suppose I could just build one myself and it may be the way I'll end up going.
Matt
Thread Starter
Member
Joined: Feb 2001
Posts: 314
Likes: 0
From: Mesquite, Texas
Car: 1992 Chevrolet RS Camaro
Engine: 305 TBI
Transmission: WC T5 conversion
Axle/Gears: Debatable . . .
No prob Matt just came accross those links and thought I'd pass them on. I'm looking to something custom as well so let me know if you get any ideas.
Member
Joined: Feb 2000
Posts: 313
Likes: 0
From: Columbus, Ohio, USA
Car: 88 IROC-Z (Sold)
Engine: 5.7L
Transmission: 700R4
racer J-
I assume that was not directed towards me? I was a bit confused reading that. lol This name in the post thing is still cracking me up.
Matt
------------------
irocet@hotmail.com
drive.to/Stang_Kilr
88 IROC-Z -- 350 L-98, 700R4, Flowmaster, K&N, MAF Sceens Gone, Airfoil, March Pullies, Comp Cams Magnum 1.6 Roller Rockers, Accel U-Groove Plugs, Accel 8.8 mm Wires, Hypertech Cap & Coil, Hypertech Chip, Hotchkis Strut Tower Brace, One Loud Stereo!
I assume that was not directed towards me? I was a bit confused reading that. lol This name in the post thing is still cracking me up.
Matt
------------------
irocet@hotmail.com
drive.to/Stang_Kilr
88 IROC-Z -- 350 L-98, 700R4, Flowmaster, K&N, MAF Sceens Gone, Airfoil, March Pullies, Comp Cams Magnum 1.6 Roller Rockers, Accel U-Groove Plugs, Accel 8.8 mm Wires, Hypertech Cap & Coil, Hypertech Chip, Hotchkis Strut Tower Brace, One Loud Stereo!
Member
Joined: Feb 2000
Posts: 313
Likes: 0
From: Columbus, Ohio, USA
Car: 88 IROC-Z (Sold)
Engine: 5.7L
Transmission: 700R4
Yeah, I am to. LOL
Matt
------------------
irocet@hotmail.com
drive.to/Stang_Kilr
88 IROC-Z -- 350 L-98, 700R4, Flowmaster, K&N, MAF Sceens Gone, Airfoil, March Pullies, Comp Cams Magnum 1.6 Roller Rockers, Accel U-Groove Plugs, Accel 8.8 mm Wires, Hypertech Cap & Coil, Hypertech Chip, Hotchkis Strut Tower Brace, One Loud Stereo!
Matt
------------------
irocet@hotmail.com
drive.to/Stang_Kilr
88 IROC-Z -- 350 L-98, 700R4, Flowmaster, K&N, MAF Sceens Gone, Airfoil, March Pullies, Comp Cams Magnum 1.6 Roller Rockers, Accel U-Groove Plugs, Accel 8.8 mm Wires, Hypertech Cap & Coil, Hypertech Chip, Hotchkis Strut Tower Brace, One Loud Stereo!
Thread
Thread Starter
Forum
Replies
Last Post
