Where can I get a connector terminal for 1227727 ECM.

I want to put my wideband O2 sensor into the MAP(2) input for the 8D_WB hac. I need to know where to find the terminal (and its' p/n)

Can anyone help??

 

C21

According tot he pinout conversion that was on Ludis' website

 

Some old info I found on the DIY-EFI site a while back.

 

I did not think the terminals would be the same for the 7730 and the 7727 b/c the 7727 is an underhood ECM exposed to the harsh engine compartment environment. So doing extensive research (hours of searching around on www.delphisecure2.com), I was able to locate the p/n's I was looking for.... and then some. So here is what I found out:

12066132 - terminals
12052924 - seals for the terminals (package of 20 p/n 12048086 seals)
12065877 - Connector 'C' (Green on my Vette)
12065878 - Connector 'D' (brown on my Vette)
12065876 - Connector 'B' (Red on my Vette)
12065875 - Connector 'A' (yellow on my Vette - manual says Yellow or Gray)
12059155 - Header for connectors 'A' and 'B' (header is what is attached to the ECM and what the connector mates to)
12059154 - Header for connectors 'C' and 'D'

I think the connectors and headers are discontinued.

 

Not only did I look up the p/n's for the terminals...... I compared the p/n the connector drawing called out witht p/n 12089660 (that the DIY-EFI site references)

I found the terminals are not the same length for starters, and the dimensions and shapes are just a bit different. I do not know if the are interchangeable, so since p/n 12066132 is available, I will try that one.

Maybe this info should be catalogged somewhere????

Attached are the drawings

 

[quote=kevosiroc]Maybe this info should be catalogged somewhere????/quote]

I saved it for future reference, nice work

 

I stickied this thread. At a later point I'll merge it into the DIY_PROM Guide book.

Thanks for the info,

BobR.

 

Glad I could help!

 

To add another piece of info.....

I was looking for this info so I could utilize the 8D wideband hac.

These are the pinouts needed for the 1227727 ECM:

C21 = MAP(2)
C18 = TPS(2)

I have all the documents to back this up, but they are too large to attach

 

Sorry: Repost

 

I have the terminals available... still on the reels for use on assembly lines.

Drop me a note off list and I can send you some.

 

Hello friend,i have a 1984 corvette crossfire and need to identify the pinouts for the stock ecm #1226430 and reconect them to the ecm#1227747,so that i can use this newer ecm,i'll apreciate your help,i need to install this ecm in my crossfire,thanks alot,if there's anything that i could do for your just leet me know,thanks a lot.

 

Might help

Vette
http://www.autozone.com/az/cds/en_us...rInfoPages.htm

747
http://www.chevythunder.com/1227747_ecm_198892.htm

 

www.eficonnection.com should have what you need. He is a member on here. S10Wildside is his name.

 

sorry for bringing this back up but I just need to know what part number this is off the ecu I have pics of that yellow connector and the ecu is 1227730 and it came out of a 92 beretta gt 3.1.






and inside it say E1 to 16
and the wire diagram I got from the dealership is saying that is post to be green can somebody clear that up also. thanks

 

any diagram conecction for connector M from ECM 96417551 XAHD DELPHI MR140 ?

the connection diagram it's neccesary for this problem:

1. 

 

Hi! I'm Ed. I have been lurking on this website for a few years. I have 2 projects underway: an '86 Camaro / 350 tpi and a '50 Chev PU that will have a 383 tpi. Life has been getting in the way of completing these projects, but I now have some time. I am in need of enough 1227727 crimp terminals to wire 2 ecm's (plus a few mistakes). If you have any available, I'd be severely in your debt. Thanks in advance for any help. Ed (pedolin@msn.com)

 

sorry, posted wrong.

 

I have some pigtails for the 727 ecm and a good used complete harness . I think the terminals have been discontinued.

 

For the crimp terminals what I do is identify the terminal I need usually by looking here:

http://ecat.delphi.com/

note the part number and then look here to buy:

Waytekwire.com

They also have the proper crimp tool at waytek for only something like $22.00.

I usually buy bags of 50 or 100 of the terminals I need.

 

I know this thread has been dead for almost 2 years but I came across it while looking for parts/info to rewire my project. I know there are some harness wiring geniuses out there that know the answers.

All of the Delphi pages listed are inactive so they are no help. I am wondering if anyone has found new sources for the ECU connectors, terminals, seals and such. I have tried google searching the part numbers listed with little to no success. I have even been searching for used terminals and or harnesses with little to no luck. So if no one has the terminal info but has the 4 connectors for the 727 ECU with all the wires/terminals still in them (wires cut long enough they can be soldered) I would be interested in those.

I know it is going to be a long shot but I am going to call a chevy dealer today and see if they can help out, if they can I will update

 

Almost anyone should be able to get a cut harness with the connectors and terminals. I should have something for you now if you want to send me a PM