Gauge location
Thread Starter
Joined: Sep 2011
Posts: 1,037
Likes: 22
From: nc
Car: 91RS
Engine: carb'd 357 vortec
Transmission: 700r4
Axle/Gears: 3.42 posi
Gauge location
I was wondering where i can put these so they look a whole lot better. I hate where they are right now. Plus I want to get a mint dash pad soon. I would love to get the OEM cluster working again or even better exchange it for a 140mph cluster and then get the proper controller for the speedo. The car was a 91rsv6 now has a 357 4spd auto
Joined: Dec 2004
Posts: 16,926
Likes: 1,016
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Gauge location
If your transmission is a cable drive you can use this Vss and a Dakota digital sgi-5e
https://www.tpiparts.net/inc/sdetail/7587
as for the tach
https://www.thirdgen.org/forums/tran...ds-double.html
the other gauges might look good in a Pilar pod.
https://www.tpiparts.net/inc/sdetail/7587
as for the tach
https://www.thirdgen.org/forums/tran...ds-double.html
the other gauges might look good in a Pilar pod.
Thread Starter
Joined: Sep 2011
Posts: 1,037
Likes: 22
From: nc
Car: 91RS
Engine: carb'd 357 vortec
Transmission: 700r4
Axle/Gears: 3.42 posi
Re: Gauge location
I bought one of these stuck it in the tranny with red drive gear and of course nothing works
https://www.carparts.com/details/Che...E&gclsrc=aw.ds
https://www.carparts.com/details/Che...E&gclsrc=aw.ds
Joined: Dec 2004
Posts: 16,926
Likes: 1,016
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Gauge location
I bought one of these stuck it in the tranny with red drive gear and of course nothing works
https://www.carparts.com/details/Che...E&gclsrc=aw.ds
https://www.carparts.com/details/Che...E&gclsrc=aw.ds
If the car was a 3.1l or tpi is the ecm still in place ?
tbi uses a Vss yellow box next to the ecm.
Trending Topics
Joined: Dec 2004
Posts: 16,926
Likes: 1,016
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Gauge location
The ecm is a Vss buffer. If it’s gone you need a gm yellow Vss buffer or a Dakota digital unit.
Joined: Dec 2004
Posts: 16,926
Likes: 1,016
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Gauge location
https://www.ebay.com/itm/86-91-Buick...er!20876!US!-1
for rear end gear ratio change and to calibrate for the speed sensor gears your better off going with the Dakota digital.
for rear end gear ratio change and to calibrate for the speed sensor gears your better off going with the Dakota digital.
Thread Starter
Joined: Sep 2011
Posts: 1,037
Likes: 22
From: nc
Car: 91RS
Engine: carb'd 357 vortec
Transmission: 700r4
Axle/Gears: 3.42 posi
Re: Gauge location
https://www.ebay.com/itm/86-91-Buick...er!20876!US!-1
for rear end gear ratio change and to calibrate for the speed sensor gears your better off going with the Dakota digital.
for rear end gear ratio change and to calibrate for the speed sensor gears your better off going with the Dakota digital.
Thread Starter
Joined: Sep 2011
Posts: 1,037
Likes: 22
From: nc
Car: 91RS
Engine: carb'd 357 vortec
Transmission: 700r4
Axle/Gears: 3.42 posi
Re: Gauge location
U da man... cant afford it till pd (payday) ... but definitely watching and if it's still there I'll grab it. Thx man.. once I had the part# I found others so no matter what I should be good
Last edited by budget builder; Feb 9, 2019 at 07:15 PM.
Joined: Dec 2004
Posts: 16,926
Likes: 1,016
From: Mile High Country !!!
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt
Re: Gauge location
The speedometer wire is in connector c207 by where the ecm use to be .
Thread
Thread Starter
Forum
Replies
Last Post
Steve86TA
Camaros for Sale
3
Nov 24, 2006 08:02 AM
Steve86TA
Engine/Drivetrain/Suspension Parts for Sale
0
Oct 29, 2006 02:10 PM
