anyone interested in a 4 inch exhaust off of an 89 iroc, has about 2000 miles on it. spintech muffler, has y pipe for hooker long tube headers that goes into a 4 inch intermediate pipe, and into the spintech muffler and out in dual 3 inch, i have quite a bit invested in this exhaust and just don't need it anymore. probably not going to build a car that need it anymore. i guess i will start at $350 or trade, possibly for a builder ls style engine. will send pics upon request.

 

Just wondering would you part with the tubing

 

i would rather not because then i have the rest just lying around lol. what do you have in mind though?

 

Well I just bought a 4 inch spintech and headman headers so allb I bwould need is pipe. And I'm tired of everyone around here telling me it can't be done or they don't have the pipe or they can't bend it

 

I am interested, please send some photos.

 

pm sent

 

just updated with some pics, and 91camaroRS, you just looking for the y-pipe? obviosly it can be done, and if you would like i can send you some detailed pics and specs on it, should be easy to have your local muffler shop build, the one here did it.

 

bump

 

ummm....pm...sent...

 

pm sent

 

I promise it can be done, bending 4" takes special equipment that very few have. I had the same deal, a friend bought a 4" Mufflex kit about 4 years ago and I wanted a similiar set-up but didn't have a grand to drop on it. So, I did what any good fabricator would do. I helped him install his, took some pics, pulled a few measurements, and...One night in my shop, and $300 later I had my own. I even built a crossmember so my 3" Y pipe would tuck really nice. I had a local exhaust shop build my Y pipe it cost $75. so for $375 I was done. and I also used a Hooker Aerochamber muffler with one sided 4" dump, looks sweet..My oponion for the money this set-up is a heck of a deal. Spintech is nice stuff and very expensive, so a free BUMP for a good deal....

 

lol thanks! thats what i thought too just trying to give someone a deal on this stuf

 

If you still have this I was curious to know if it woulor work with a spohn t56 crossmember in there.

 

if i was closer i would be all over it ! good luck with the sale

 

wish you were closer I would pcik it up even though i only need the 4inch back.

 

Send pics and a price to ship to 72104
allen.bray64@yahoo.com

 

not too sure realy? i could get you closer pics of the y pipe if you would like. i dont have any pics of it in the car though

 

i will get a quote for you tomorrow

 

Interested. Was your car lowered at all? I have a 86bird with a eibach sportline drop, any ideas if this will clear it?

Mark

 

the car it was on was lowerd 2 inches but never saw street time, just track. but at that low of a stance it did drag some on good bumps

 

PM sent

 

Could you please send a shipping quote to 34772 to bbut2@osceola.org

 

87 firebird, im wondering about ground clearance, I have a driveshaft loop also. will that clear. Also it looks like it cuts over under the drive shaft. Very interested. I was running long tubes and 3" under the floor pans on back but it dragged alot, So im just curious about this also being 4"

 

the car it was on had a driveshaft loop too, it cleared. and it tucks up into the car pretty nice it didn't drag too bad but i dunno for a street car

 

sorry to all that are wanting a quote on shipping, i promise i am getting it for ya, its just a hassle to load it up everytime and do all of that. as soon as i get it i will post your zip and the price they gave me, thanks!

 

interested also

as for shipping quotes. If you had it weighed once and know the size go here
http://postcalc.usps.gov/

My zip is 34229

 

I'm very interested if you still have it send mr a qoute for shipping to 89101 to carranzafermin@aol.com and I will email you about the price k and what headers did you have on this motor huh!!

 

bump.....

 

sale pending, if it falls through i will get you all quotes still though! sorry its taken so long, i have been out of town working almost everyday and havn't had a chance to take this in.

 

cant get buyer to answer so pmed all quotes, if i let you out im sorry let me know and i can get you one fast now!

 

Thanks for the PM. but found something local. Thanks anyways !

 

hey no problem, sorry it took so long

 

if you seprate let me know. I'll buy the over acle back right now. Dont need the Y pipe I'm a turbo car.

 

sold! thanks guys