great deal here!!
Thread Starter
Senior Member
Joined: Sep 2007
Posts: 678
Likes: 0
From: NORTH EAST GA
Car: 84 z28
Engine: 355
Transmission: TH350
Axle/Gears: one wheel peel
great deal here!!
just found out i have a baby on the way so i have some cool go fast goodies for sale from my camaro project that got scrapped.
1300 cash buys EVERYTHING you see, as is where is. will not sell seperatley
built 355 four bolt main 2 piece rear seal engine
specs: eagle esp crank, eagle sir i beam rods, speed pro pistons (flat tops) all balanced and put together using spicer bearings and rings with fel pro gaskets. bottom end cost me $1500 and this engine has only about 60 miles on it. (i put it in my car, broke it in, then pulled it to paint my engine bay. it never got put back in the car). also has a crane 498 498 lift cam with a 292 duration, manly push rods, crane 1.7 roller rockers, eldelbrock performer rpm intake holley 650 with electric choke. motor has full blinged out dress up kit. chrome 5 qt pan, timing cover, aluminium tall valve covers, and i big holley chrome round air cleaner. also has hei dist, with big accel wires and plugs, AND a griffen aluminuim radiotor for a 3rd gen.
will also throw in a serpentine belt system for a iroc engine, hooker long tube headers, and a th350 short shaft transmission (missing torque convertor, had a 3500 stall but was sold a few years back).
im selling this all as parts because it has been years since ive ran this engine/trans and i dont want anyone getting burned. expect to put rings bearings and a gasket set in this engine, expect to need a new carb/plugs wire and oil. expect the trans is just a rebuildable core. but i will say that all this stuff WAS running great in my 83 z28 before i took it out.
emails to ga_fireman1989@yahoo.com, or pm me. emails are best
1300 cash buys EVERYTHING you see, as is where is. will not sell seperatley
built 355 four bolt main 2 piece rear seal engine
specs: eagle esp crank, eagle sir i beam rods, speed pro pistons (flat tops) all balanced and put together using spicer bearings and rings with fel pro gaskets. bottom end cost me $1500 and this engine has only about 60 miles on it. (i put it in my car, broke it in, then pulled it to paint my engine bay. it never got put back in the car). also has a crane 498 498 lift cam with a 292 duration, manly push rods, crane 1.7 roller rockers, eldelbrock performer rpm intake holley 650 with electric choke. motor has full blinged out dress up kit. chrome 5 qt pan, timing cover, aluminium tall valve covers, and i big holley chrome round air cleaner. also has hei dist, with big accel wires and plugs, AND a griffen aluminuim radiotor for a 3rd gen.
will also throw in a serpentine belt system for a iroc engine, hooker long tube headers, and a th350 short shaft transmission (missing torque convertor, had a 3500 stall but was sold a few years back).
im selling this all as parts because it has been years since ive ran this engine/trans and i dont want anyone getting burned. expect to put rings bearings and a gasket set in this engine, expect to need a new carb/plugs wire and oil. expect the trans is just a rebuildable core. but i will say that all this stuff WAS running great in my 83 z28 before i took it out.
emails to ga_fireman1989@yahoo.com, or pm me. emails are best
Thread Starter
Senior Member
Joined: Sep 2007
Posts: 678
Likes: 0
From: NORTH EAST GA
Car: 84 z28
Engine: 355
Transmission: TH350
Axle/Gears: one wheel peel
Re: great deal here!!
if you want to pay freight from south eastern usa to canada and arrange for a truck to pick it all up
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
camaroinmotion
Exterior Parts for Sale
2
Sep 2, 2015 08:25 AM





