Does anyone have any pics of camaro/firebirds with side pipes exaust systems. Im curious to get one but, im afraid itll burn the ground effect. IF possible please post a pic or a site were i can see a pic of it on a third gen.

------------------
92' camaro
New 305 block TPI conversion, Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system.
Soon to come!!!
Procharger system 12lbs o boost.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

hmmm...i'm not sure. I have seen some with side exiting exhaust but not the actual side pipes. Also, don't you think that would make clearance an even bigger problem??

 

If you really wanted side exits, it would probably be wiser to remove the side ground effects. Or you could cut a curved upside down U on the effects and stick the pipe through that, before about 2-3" in front of the rear wheels.

------------------
--Steve S--
1984 Trans Am 305 LG4, 5 speed
Daily Driver, Flowmaster 80 Series
NOW FEATURING: Holley 600 cfm & vacuum advance

 

I saw these before. They were on an 86 camaro i believe. The car had no gfx. In my view it was the ugliest thing i have ever seen in my life. I have seen ricers that looked better than this car. It would have been a nice looking camaro, if it didnt have the side exhaust. The ones I saw were huge, and bulky. They looked like the person ripped off smoke stacks from a mack truck, and just mounted them to his car. I dont know if this is the same side exhaust that you want, but the one i saw was hideous.

 

yeah i guess your all right, i was just curious cause i never seen one just wanted to take a look at one.

------------------
92' camaro
New 305 block TPI conversion, Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system.
Soon to come!!!
Procharger system 12lbs o boost.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

http://members.aol.com/carndrvr/camaro1.jpg
------------------
Faster than a bullet, these are F-body's don't even pull it.



[This message has been edited by redcamaro83 (edited February 24, 2001).]

 

Some older Corvette's and the late 60's & 1970 Plymouth Cuda had this feature, i really like it, if you planned it right, you could probably make it look really decent on a 3rd gen.

 

yeah i know i have it on my 71' duster but just wanted to see how it looked on third gen camaro. It didnt look that bad on the blue z-28 what happend to the front skirt.

------------------
92' camaro
New 305 block TPI conversion, Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system.
Soon to come!!!
Procharger system 12lbs o boost.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

Wow. I guess i was wrong. That blue camaro looks great with the side pipes. I guess it is just that the one i saw was a different style. The one i saw looked totally different. I like the ones on the blue camaro alot.

 

The older vettes had them simply for clearance problems when running a big block. There was no room for exhaust under the car so the factory mounted the side pipes.

 

Umm.. that's not really a sidepipe on the blue Camaro, side exit maybe.

 

my nieghbor has a 90 firebird and he is wanting to put side pipes on it, not just side exhaust like the blue camaro pic. i dont think it will be to hard to do as long as he gets the correct length sidepipes, then he is going to have to get headers, and have custom pipe bent. he keeps talking about it, if he ever orders the pipes and i get them mounted, i will post pics.

------------------
Wide Open Till You See God...Then Brake