HELP, exhaust tip ideas needed.
04-14-2009, 09:14 PM
#1
Senior Member
Thread Starter
HELP, exhaust tip ideas needed.
i still can't decide what tips to put on. i need to get this done asap. i am looking at weld on, not any clamp on. opions/pics would help. thanks.
04-15-2009, 12:44 PM
#2
COTM Editor
iTrader: (11)
Join Date: Mar 2006
Location: WINDSOR, CO
Posts: 4,098
Likes: 0
Received 12 Likes
on
12 Posts
Car: 91 Z28, 87 SC, 90 IROC, 92 RS
Engine: LS1, 305 TPI, L98, NADA
Transmission: T56, 700r4's, and NADA
Axle/Gears: 3.89, 3.42, 3.23, NADA
Re: HELP, exhaust tip ideas needed.
I say put 4th gen z28 tips in the center of the black stripe. Don't polish them, leave them black.
Or don't run any at all.... I'm gonna be getting rid of mine SOON!
Or don't run any at all.... I'm gonna be getting rid of mine SOON!
04-15-2009, 08:33 PM
#4
Senior Member
Thread Starter
Re: HELP, exhaust tip ideas needed.
ok, so i'm thinking long 18" round slash tips or z28 (blk or chrome), or just turn downs. i think center exit would be cool. just don't know for sure.
04-15-2009, 08:55 PM
#5
Senior Member
iTrader: (4)
Join Date: May 2006
Location: Beloeil, Quebec
Posts: 704
Likes: 0
Received 2 Likes
on
2 Posts
Car: IROC-Z
Engine: LSx
Transmission: T56
Axle/Gears: Fabbed 9"
Re: HELP, exhaust tip ideas needed.
Dont put any. Round tips dont go with the 3rd gen body style. If you definately want some, I vote for a rectangular type like the early 4th gen design.
04-15-2009, 09:12 PM
#6
Banned
iTrader: (12)
Join Date: Jul 1999
Location: Bertram (outside Austin), TX
Posts: 12,212
Likes: 0
Received 10 Likes
on
10 Posts
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: HELP, exhaust tip ideas needed.
I vote no tips, or if you just really like/want tip.....A notched rear bumper with rectangular tip tucked up into the notch.
1 center or dual notches....Either would look good to me.
My GTA came with round Magnaflow tips, but I'm gonna switch to a side exit exhaust, with a low-pro rectangular tip.
1 center or dual notches....Either would look good to me.
My GTA came with round Magnaflow tips, but I'm gonna switch to a side exit exhaust, with a low-pro rectangular tip.
04-15-2009, 09:27 PM
#7
Supreme Member
iTrader: (7)
Join Date: Jun 2008
Location: Minnesota
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROC-Z
Engine: 370 LSX, LS3 Top End
Transmission: Built T-56
Axle/Gears: 9" Aluminum Center 3.89's
Re: HELP, exhaust tip ideas needed.
I vote no tips, or if you just really like/want tip.....A notched rear bumper with rectangular tip tucked up into the notch.
1 center or dual notches....Either would look good to me.
My GTA came with round Magnaflow tips, but I'm gonna switch to a side exit exhaust, with a low-pro rectangular tip.
1 center or dual notches....Either would look good to me.
My GTA came with round Magnaflow tips, but I'm gonna switch to a side exit exhaust, with a low-pro rectangular tip.
Trending Topics
04-17-2009, 09:50 PM
#8
Senior Member
Thread Starter
Re: HELP, exhaust tip ideas needed.
well, i am going to get a set of newer z28 and slide them on and see how they look.
04-17-2009, 10:05 PM
#9
Supreme Member
Join Date: Apr 2006
Location: Morganton, NC
Posts: 1,206
Likes: 0
Received 4 Likes
on
2 Posts
Car: '92 T/A WS6 Vert/1956 Chevy Nomad
Engine: 350 TPI
Transmission: 700r4 w/ Transgo Kit
Axle/Gears: 3.42 LSD
Re: HELP, exhaust tip ideas needed.
Now, obviously mine is a Trans Am, but I think these tips would look even better on your car:
http://www.tpsphotography.com/TA03.jpg
Picked them up on Ebay. They are stainless. Can't remember what I paid but I think it was around $50.
http://www.tpsphotography.com/TA03.jpg
Picked them up on Ebay. They are stainless. Can't remember what I paid but I think it was around $50.
04-18-2009, 01:07 AM
#10
Senior Member
iTrader: (9)
Join Date: Jun 2002
Location: La Mirada, California
Posts: 742
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: L98 350 TPI
Transmission: 700R4
Axle/Gears: ZT LSD with 3.42 - LS1 brakes
Re: HELP, exhaust tip ideas needed.
I got the 3'' slash cuts, polished stainless steal. You can see them in the vids in my sig
Thread
Thread Starter
Forum
Replies
Last Post
NinjaNife
Tech / General Engine
27
08-23-2015 11:49 AM
