parts needed
Thread Starter
Supreme Member
iTrader: (7)
Joined: Mar 2005
Posts: 1,926
Likes: 3
From: mid GA
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
parts needed
i need a couple little things for my camaro but i also need some other stuff if its priced right.
power antenna or the stick one that doesnt go up and down.
passenger seat belt retractor (got this)
washer solvent bottle (got this)
female end front seatbelts (got this)
driver side mirror. just need the glass mirror part
plug that plugs into the bottom of the maf sensor and a little bit of the wire
and i really dont have to have these things below but if the price is right i do
complete dash
center console with grey carpet.
full set of black carpet
305 heads aftermarket or just the 081's
headers and y-pipe any brand.
and i would like to find someone local to me that has a TIG welder for sell.
i might have forgot a couple things. if i think of them i will post them also i have a couple things to trade.
power antenna or the stick one that doesnt go up and down.
passenger seat belt retractor (got this)
washer solvent bottle (got this)
female end front seatbelts (got this)
driver side mirror. just need the glass mirror part
plug that plugs into the bottom of the maf sensor and a little bit of the wire
and i really dont have to have these things below but if the price is right i do

complete dash
center console with grey carpet.
full set of black carpet
305 heads aftermarket or just the 081's
headers and y-pipe any brand.
and i would like to find someone local to me that has a TIG welder for sell.
i might have forgot a couple things. if i think of them i will post them also i have a couple things to trade.
Last edited by maroon88iroc; Jul 19, 2005 at 10:49 PM.
Senior Member
iTrader: (42)
Joined: Jun 2001
Posts: 929
Likes: 10
From: Nicholasville,KY
Car: 1992 Camaro RS
Engine: 415ci LS3
Transmission: T56
Axle/Gears: 3.89
What color seatbelts do you need? I have Gray ones.
Also have a complete set of Black Carpet from an 86 Iroc in really good shape, and the washer solvent bottle...........jt
Also have a complete set of Black Carpet from an 86 Iroc in really good shape, and the washer solvent bottle...........jt
Thread Starter
Supreme Member
iTrader: (7)
Joined: Mar 2005
Posts: 1,926
Likes: 3
From: mid GA
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
the seatbelts i need are gray. and i dont need a whole set all i need is the passenger side retractor and the front "female's" i think thats what you call them
also kyle you have e-mail all the others i will send you a pm.
and the bigger stuff i listed i would like to keep local b/c shipping would probably kill me.
also kyle you have e-mail all the others i will send you a pm.
and the bigger stuff i listed i would like to keep local b/c shipping would probably kill me.
i have a set of flowtec headers with some surface rust on em, but brand new, used em to break in a motor, then the car sat, it burned off the primer and here we are...50 bucks plus shipping
Trending Topics
Senior Member
iTrader: (42)
Joined: Jun 2001
Posts: 929
Likes: 10
From: Nicholasville,KY
Car: 1992 Camaro RS
Engine: 415ci LS3
Transmission: T56
Axle/Gears: 3.89
Sorry I just checked my seatbelts, i may have already sold the fronts. All i could find was the rears. I do have a set from a 95 Formula though. They are Dark Gray, there is a tech article in using them in a thirdgen. $40.00 shipped for the fronts.....jt
Thread Starter
Supreme Member
iTrader: (7)
Joined: Mar 2005
Posts: 1,926
Likes: 3
From: mid GA
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
alright so far i have scored a couple things. i will mark them off the list but i still need this other stuff. the things i got are washer bottle, front seat belt ends, and passenger seat belt retractor. i still need this other stuff guys lmk something.
Junior Member

Joined: Mar 2004
Posts: 69
Likes: 0
From: Reading Pa
Car: 1989 irocz convert
Engine: 383 tpi
Transmission: 4 spd auto
i have the stock heads off my 305...complete..82,000 miles. Make me an offer. I also have the original manifolds and y pipe with the air tubes--$25 plus shipping.
Thread Starter
Supreme Member
iTrader: (7)
Joined: Mar 2005
Posts: 1,926
Likes: 3
From: mid GA
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
i have already e-mailed you about it. in fact i have been talking to you for the past couple of days about it through e-mail. my e-mail adress is maroon88iroc@yahoo.com.
Member

Joined: May 2003
Posts: 435
Likes: 0
From: Huntsville, Al
Car: ‘92 Z28
Engine: 350
Transmission: Auto
Axle/Gears: 3.23
I have a good console for you. It is all black, no carpet, includes the pad. Power swithch cutouts for windows and hatch.
There are 3 screw holes in the plastic on the passenger side. Looks like someone had installed a cell phone there. The upper piece is in good shape too. there is a small hole (1/8" dia) drilled below the hatch switch cutout (looks like an led for an alarm).
Let me know.
There are 3 screw holes in the plastic on the passenger side. Looks like someone had installed a cell phone there. The upper piece is in good shape too. there is a small hole (1/8" dia) drilled below the hatch switch cutout (looks like an led for an alarm).
Let me know.
Thread Starter
Supreme Member
iTrader: (7)
Joined: Mar 2005
Posts: 1,926
Likes: 3
From: mid GA
Car: 88 IROC
Engine: 305 TPI w/ l98 cam
Transmission: T5 5-speed
Axle/Gears: 3.45 posi disc 9 bolt
i also need some poly sway bar bushings and maybe endlinks for the stock sway bars on my iroc.
Thread
Thread Starter
Forum
Replies
Last Post




