[NJ] 4th gen Rear end (no brakes & backing plates)

Thread Tools
 
Search this Thread
 
Old Jan 21, 2018 | 08:27 AM
  #1  
JohnnyIroc's Avatar
Thread Starter
Member
iTrader: (3)
 
Joined: Aug 1999
Posts: 164
Likes: 9
From: Fords, NJ, US
Car: 85 TA
4th gen Rear end (no brakes & backing plates)

This rear was just pulled out for a Ford 9". Previous owner said rear was whining. I believe its a 3.23 gear with posi. I dont know exact year but I know it was not an abs unit. Must be picked up. $50 obo.




Reply
Old Jan 21, 2018 | 07:50 PM
  #2  
firebrdo88's Avatar
Junior Member
20 Year Member
iTrader: (1)
 
Joined: Apr 2006
Posts: 86
Likes: 0
From: Perrysburg, Ohio
Car: 1988 Pontiac Firebird
Engine: 400 sbc
Transmission: TH400
Axle/Gears: Ford 9" 3.50 35 Spline
Re: 4th gen Rear end (no brakes & backing plates)

That is a ABS rear end.... That is what the gear is next to the ring gear.....
Reply
Old Feb 11, 2018 | 04:43 PM
  #3  
mizz0313's Avatar
Junior Member
iTrader: (1)
 
Joined: Apr 2011
Posts: 64
Likes: 1
From: Pittsburgh Pennsylvania
Car: 92 Camaro RS Heritage Edition PoloG
Engine: L31 Vortec
Transmission: 4160e
Axle/Gears: 4th Gen Torsion Rear/ 3.42s
Re: 4th gen Rear end (no brakes & backing plates)

Originally Posted by JohnnyIroc
This rear was just pulled out for a Ford 9". Previous owner said rear was whining. I believe its a 3.23 gear with posi. I dont know exact year but I know it was not an abs unit. Must be picked up. $50 obo.




where are located?
Reply
Old Feb 13, 2018 | 04:05 AM
  #4  
JohnnyIroc's Avatar
Thread Starter
Member
iTrader: (3)
 
Joined: Aug 1999
Posts: 164
Likes: 9
From: Fords, NJ, US
Car: 85 TA
Re: 4th gen Rear end (no brakes & backing plates)

Central New Jersey near exit 10 off turnpike.
Reply
Old Feb 14, 2018 | 08:03 AM
  #5  
mizz0313's Avatar
Junior Member
iTrader: (1)
 
Joined: Apr 2011
Posts: 64
Likes: 1
From: Pittsburgh Pennsylvania
Car: 92 Camaro RS Heritage Edition PoloG
Engine: L31 Vortec
Transmission: 4160e
Axle/Gears: 4th Gen Torsion Rear/ 3.42s
Re: 4th gen Rear end (no brakes & backing plates)

not familiar with jersey at all. Typed on central New Jersey found a few businesses and looked at commute time. If that’s around your area I’m looking at about 5.5 hours. Really thinking about making the drive but don’t know a whole lot about rears. I know you say it’s whining could this just use a rebuild kit or do you think it needs a complete overhaul. I know you don’t have all the info on this rear but if you can give any advice it would help me out. Thanks.
Reply
Old Feb 18, 2018 | 09:03 AM
  #6  
JohnnyIroc's Avatar
Thread Starter
Member
iTrader: (3)
 
Joined: Aug 1999
Posts: 164
Likes: 9
From: Fords, NJ, US
Car: 85 TA
Re: 4th gen Rear end (no brakes & backing plates)

The previous owner road raced it so im sure it atlest needs bearings. It was also behind 550 ftlbs of tq and a manual trans. Gears and posi do look in good shape thou. Its up to you. If you dont get out here by next saturday its going to scrap yard. thanks
Reply
Old Feb 23, 2018 | 02:40 PM
  #7  
mizz0313's Avatar
Junior Member
iTrader: (1)
 
Joined: Apr 2011
Posts: 64
Likes: 1
From: Pittsburgh Pennsylvania
Car: 92 Camaro RS Heritage Edition PoloG
Engine: L31 Vortec
Transmission: 4160e
Axle/Gears: 4th Gen Torsion Rear/ 3.42s
Re: 4th gen Rear end (no brakes & backing plates)

Any chance on shipping the carrier? Truck fuel pump went out this week so I left this be not wanting to waste your time. But just thought of purchasing the carrier and getting a v6 rear local. Let me know thanks
Reply
Old Mar 4, 2018 | 02:52 PM
  #8  
JohnnyIroc's Avatar
Thread Starter
Member
iTrader: (3)
 
Joined: Aug 1999
Posts: 164
Likes: 9
From: Fords, NJ, US
Car: 85 TA
Re: 4th gen Rear end (no brakes & backing plates)

Well since 2 have already no showed. Who want this rear for $20. Come pick it up, or to the garbage it goes in a few weeks. Its sitting on my back lawn. so one the grass starts growing its gotta go.
Reply
Old Mar 27, 2018 | 12:09 AM
  #9  
hwcoll95's Avatar
Senior Member
20 Year Member
iTrader: (6)
 
Joined: Mar 2002
Posts: 587
Likes: 1
From: middle TENNESSEE
Car: 1989 Iroc rebuild
Engine: 355 carb'd
Transmission: 5spd
Axle/Gears: 3:08 pos for a while
Re: 4th gen Rear end (no brakes & backing plates)

sent you a pm
Reply
Old May 18, 2018 | 10:49 AM
  #10  
Dee555's Avatar
Member
20 Year Member
 
Joined: Apr 2002
Posts: 131
Likes: 0
From: New Jersey
Car: 89 Iroc - 84 Trans Am -84 Corvette
Engine: 350 TunedPort
Transmission: 700R/T-5 World Class
Axle/Gears: Posi/Ausi/Disc/3.08
Re: 4th gen Rear end (no brakes & backing plates)

Is this rear still available, I'm in the area and can pick up,, email me at
bondouvich@aol.com
Thank you
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
88FormulaKiller
Engine/Drivetrain/Suspension Parts for Sale
2
Jun 7, 2016 01:31 PM
Z28ricer
Brakes
14
Jan 9, 2002 08:41 AM
jody92RS
Transmissions and Drivetrain
7
Feb 16, 2001 07:49 PM




All times are GMT -5. The time now is 01:23 AM.