[NJ] SLP 1 3/4" stainless headers
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
SLP 1 3/4" stainless headers
Sale pending
What is pictured is for sale
This set is with the air tubes and does have part of the Y pipe, I will get an updated picture of that next week. The Y pipe is cut, I was going to use that for my next exhaust setup but I wont need it now. The one primary tube is dented to clear the steering arm? I bought the headers this way from a member on here years ago. I bought them with the intent of needing them to get through inspection every two years. NJ does not do a through inspection any longer and I am also going LSx in my car since I took it apart. I would like $225 shipped obo for this set.
What is pictured is for sale
This set is with the air tubes and does have part of the Y pipe, I will get an updated picture of that next week. The Y pipe is cut, I was going to use that for my next exhaust setup but I wont need it now. The one primary tube is dented to clear the steering arm? I bought the headers this way from a member on here years ago. I bought them with the intent of needing them to get through inspection every two years. NJ does not do a through inspection any longer and I am also going LSx in my car since I took it apart. I would like $225 shipped obo for this set.
Last edited by scooter; Aug 26, 2011 at 04:36 PM.
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
.............
Last edited by scooter; Aug 26, 2011 at 04:34 PM.
Joined: Aug 2006
Posts: 12,812
Likes: 110
From: Central NJ
Car: 86 Trans Am
Engine: 408 stroker sbc
Transmission: TKO600
Axle/Gears: Moser full floater m9, 3:70 trutrac
Re: SLP 1 3/4" stainless headers
will these fit on my 3.1 v6 if i paint them green?
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
.............
Last edited by scooter; Aug 26, 2011 at 04:34 PM.
Supreme Member
Joined: May 2005
Posts: 1,058
Likes: 4
From: Malvern, Arkansas
Car: 90 IROC 2-92 Zs blk vert & prpl
Engine: stealth ram brodix track 1 ful port
Transmission: 700r4 4l80e
Axle/Gears: iroc 375 lokr 92 Z 277 pos vert 327
Re: SLP 1 3/4" stainless headers
How much shipped to 72104?
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
....................
Last edited by scooter; Aug 26, 2011 at 04:34 PM.
Trending Topics
Joined: Jul 2005
Posts: 1,428
Likes: 2
From: Guilford, Connecticut
Car: 1988 IROC-Z camaro
Engine: 355 TPI
Transmission: tko 500
Axle/Gears: Dana 44 3.31 posi pbr brakes
Re: SLP 1 3/4" stainless headers
Ug i wish i had the extra spending money right now for that first set. Good luck with the sale.
Junior Member
iTrader: (1)
Joined: Jun 2010
Posts: 28
Likes: 0
From: pasadena tx
Car: 85 irocz
Engine: 383
Transmission: tci 700r4
Axle/Gears: 9" 3.89 locker
Re: SLP 1 3/4" stainless headers
how much for the non air pipe headers to pasadena tx 77506
Last edited by drew.davis83; Jun 16, 2011 at 06:22 PM.
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
..................
Last edited by scooter; Aug 26, 2011 at 04:35 PM.
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
.................
Last edited by scooter; Aug 26, 2011 at 04:35 PM.
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Thread Starter
Joined: Sep 1999
Posts: 4,353
Likes: 308
From: NJ
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: SLP 1 3/4" stainless headers
Bump. I also put these in the bead cabinet and cleaned them up. They look a lot better now, minus the dents.
Junior Member
Joined: Mar 2011
Posts: 48
Likes: 0
From: Grizzly Flats, CA
Car: 86 Camaro, IROC springs & bars
Engine: Mild 350,Q-jet,headers
Transmission: M-21, 12#flywheel
Axle/Gears: 98 7.5, 3.73 torsen.
Re: SLP 1 3/4" stainless headers
I'm also interested, call if still available, 530-642-9563.
Thread
Thread Starter
Forum
Replies
Last Post
redformula88
Engine/Drivetrain/Suspension Parts for Sale
2
Oct 14, 2015 06:08 PM
blackandblue02
Camaros for Sale
0
Sep 10, 2015 08:19 PM