Selling this motor because I am stepping up to a full out race motor. This one is streetable and can be driven on streets if you need to do a cruise or something for a race. or just to a meet or whatever. motor is in good shape has always had mobil vr1 oil 20-50 in it. it has about 45-50 total passes on it. 35-40 of them being 1/8 mile only. motor is capable of up to 300hp

any questions you can pm here or email me at dudster2002@yahoo.com

paypal will be ashtonkesterson@gmail.com

Will sell complete for 5500 or i will tear it apart and sell seperate.
parts listed below do not include shipping. I will sell the arp hardware too
if you are interested. complete motor will be intake down to oil pan including starter
and flexplate.







396 ci.
Chevrolet 350 sbc 4 bolt main roller truck block. oil passages smoothed and clearanced.
4.040 bore. 3.875 stroke and 6 in rods 750
Callie's compstar 3.875 forged crank. 400
Manley 6" h beam forged rods. 275
Diamond gas ported nitrous pistons. 375
Acl bearings
Billet main caps and front main is strapped
Everything is arp studded
melling hv oil pump. 25



Bottom end good for 900-1000 hp easily

Afr 210 cc heads. 76cc chambers. Gasket matched and mildly cleaned up intake ports. Titanium retainers. Valve springs good for .700 lift
Heads are clearances for pushrods and all. 1100

Commotion custom grind cam. 260/266 624/608 on a 112 lsa. 225

Crower severe duty roller lifters. 250
Crower shaft mount rockers. 1.6/1.5 ratio. 600

not sure on exact part number but this is the cost on them
http://www.summitracing.com/parts/cro-74139f

Blp custom pushrods. 50

Brodix Hv1000 intake also gasket matched. 4150 carb base 300
http://www.summitracing.com/parts/bro-hv1000

Pioneer flex plate. 40
7 quart oil pan with trap door. 100


heres some videos of it running. only times i got to run it.

 

11.8:1 compression also

10.3@133 on motor.

9.27@147 on 200 kit

 

Make offers people.

 

Really nice motor. But, IMHO, that thing would be a royal pain on the street. Maybe that's why interest is weak. Anyway, GLWS.

 

Why? Not much different than mine and mine is as street able as my dd gas mileage worse but that's all!

 

I was thinking the same thing, 98% of this crowd still has catalytic converters on their cars, and are still A/C equipped, streetable has a
completely different meaning for guys like us, Good Luck tho!

 

Never claimed it to be a daily driver set-up. To any interested dont be discouraged sounds like a great street strip motor.

 

BUMP just went 8s in it. new 1/8 mile is 5.62@122 now also.

5000 will take it intake to oil pan

 

parting it out who wants what

 

Try your local Craigslist and yellow bullet keep bumping it till it sells! More serious buyers on the bullet. Serious motor and no reason it won't sell b patient!

 

Nice engine and video, GLWS.

 

heads intake rockers and pushrods are pending sale

 

how you doing brother do you have any pictures of the crank and rods

 

how you doing brother do you have any pictures of the crank and rods

 

I have not torn apart the bottom end but I do have pictures of the pistons and cylinder rods right now. I can email them to you if you would like.

 

Sick... Everyone need 9 just like it lol... Free bump for ya...

 

That motor will sell as a whole...patience is the key. With an 8 second pass...I would not even consider selling! What is the reason if you don't mind me asking?

 

I met all my goals with this motor. I am now building a bigger badder setup with new goals.

 

Complete motor still for sale. Hit me up people

 

450 for rockers plus shipping. Deal of the week

 

How much for your oil pan (if any is left lol) studs for oil pan. And your harmonic balance. Just want to make sure that that harmonic balance is a external balance correct? part number 917080?
Shipped to 16501 Erie,Pa

 

It's externally balanced. Oil pan is still for sale. I just used regular bolts for it. 175 shipped for the pan and balancer.

 

This is a two piece engine oil pan correct?

 

WOULD LIKE TO KNOW ALSO

AND IS IT PASSENGER SIDE DIPSTICK TOO ??

 

1 piece seal oil pan passenger side dipstick

 

caribbean 85 if you want the the oil pan its yours no use for me. Kowboy I apologize, What will you do for just the harmonic balance?

 

80 shipped for balancer

 

Rockers sold. Balancer sold.

 

I'm assuming the block is a 1 piece RMS?

 

Yes it is. Currently out of town for one week. I'll be back soon. Thanks.

 

1 piece seal pan - no good for me either

 

pm sent

 

Didnt get anything

 

Pm sent

 

pm sent

 

i cant believe your started parting a badass motor like that. that thing shoulda sold complete. Very similar to my 383 and your car looks like a drag setup of mine. My car is a street car, flat black very similar to yours minus the skinnys and slicks. My motor is a slightly tamer 11:2:1 383 and i have no issue driving it any day of the week once its warmed up lol.
Man i commend you on a well built car GLWS. great price for that motor too!

 

sent you a PM

 

bump

 

WOWW -love those videos... car looks just like mine


Good thing you aren't closer I would be tempted to buy it

 

In your description you said "Motor is capable of 300HP"? I would think it would have a whole lot more than this? Nice motor for sure.

 

I believe he's referring to a 300 shot of NOS....

 

Gotcha gotcha... I should have figured that. I just read it quick and thought 300hp and he's pulling wheelies... LOL

 

All I have left is as follows.

The bare block with oil pump and billet mains and studs. 300 local pick up
Oil pan 40 shipped
Flexplate 30 shipped

 

Can sold?

 

how much for the heads? and cam? and shipped to 17701

 

bump!!!!

 

Picture and info on flexplate please.