Camshaft, Pypes muffler, stud girdles, TPI duct
#1
Member
Thread Starter
iTrader: (4)
Join Date: Apr 2004
Location: New Orleans
Posts: 318
Likes: 0
Received 0 Likes
on
0 Posts
Car: CAMARO
Engine: 383 LT1
Transmission: T 56
Axle/Gears: 3.73
Camshaft, Pypes muffler, stud girdles, TPI duct
Hello I am selling a few parts that I have had stored in my garage and I am not going to use them.
Crower cam E33015 The cam was in the engine that has very little run time on it but zero miles.
Part Number/Work Order Number E33015
Engine Application 350 CHEVROLET
Grind Number SPECIAL
ADVERTISED CAMSHAFT SPECIFICATIONS:
INTAKE: Duration: 293º Lift: .549 Clearance Hot: .018
EXHAUST: Duration: 301º Lift: .570 Clearance Hot: .020
The specifications listed above are based on a rocker arm ratio of
1.50 IN
1.50 EX
LOBE SEPERATION 112º
Duration at .050" Intake: 260º
Exhaust: 268º
4 degrees of advance have been ground into this Camshaft.
I would like to gt 150 shipped
Stud Girddles I would like 50 Shipped
Valve Covers 30 plus shipping
Edelbrock Carb 1407 750cfm needs to be rebuilt I would like 150 shipped OBO
TPI Ducts over the radiator I would like 50 plus shipping
Pypes Muffler 3.5 inch Brand new, never used 80 shipped.
Crower cam E33015 The cam was in the engine that has very little run time on it but zero miles.
Part Number/Work Order Number E33015
Engine Application 350 CHEVROLET
Grind Number SPECIAL
ADVERTISED CAMSHAFT SPECIFICATIONS:
INTAKE: Duration: 293º Lift: .549 Clearance Hot: .018
EXHAUST: Duration: 301º Lift: .570 Clearance Hot: .020
The specifications listed above are based on a rocker arm ratio of
1.50 IN
1.50 EX
LOBE SEPERATION 112º
Duration at .050" Intake: 260º
Exhaust: 268º
4 degrees of advance have been ground into this Camshaft.
I would like to gt 150 shipped
Stud Girddles I would like 50 Shipped
Valve Covers 30 plus shipping
Edelbrock Carb 1407 750cfm needs to be rebuilt I would like 150 shipped OBO
TPI Ducts over the radiator I would like 50 plus shipping
Pypes Muffler 3.5 inch Brand new, never used 80 shipped.
#2
Member
Thread Starter
iTrader: (4)
Join Date: Apr 2004
Location: New Orleans
Posts: 318
Likes: 0
Received 0 Likes
on
0 Posts
Car: CAMARO
Engine: 383 LT1
Transmission: T 56
Axle/Gears: 3.73
Re: Camshaft, Pypes muffler, stud girdles, TPI duct
I have pictures but they are too large to upload, but I will try to compress and update.
#7
Member
Thread Starter
iTrader: (4)
Join Date: Apr 2004
Location: New Orleans
Posts: 318
Likes: 0
Received 0 Likes
on
0 Posts
Car: CAMARO
Engine: 383 LT1
Transmission: T 56
Axle/Gears: 3.73
Re: Camshaft, Pypes muffler, stud girdles, TPI duct
Yeah I can pm me you phone number or email and I will send it.
Trending Topics
#9
Want a title? Post!
iTrader: (1)
Join Date: Mar 2011
Location: TUCSON AZ
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 IROC-Z28
Engine: Monster 355
Transmission: Borg Warner Super T10
Axle/Gears: 28 spline, locker, 3.42s
Re: Camshaft, Pypes muffler, stud girdles, TPI duct
3/8 or 7/16s on the stud girdle?
#10
Member
iTrader: (7)
Join Date: Jan 2013
Location: Right here in front of you
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Iroc T-top
Engine: 350 w/typical bolt-ons
Transmission: 5 speed
Axle/Gears: 3.42 zexel, TEN chromoly 28 splines
Re: Camshaft, Pypes muffler, stud girdles, TPI duct
Can you send me a pic of the valve covers?
mcmxgateman@gmail.com
mcmxgateman@gmail.com
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
08-12-2015 03:41 PM