[Sold] Rear Louver Mounting Hardware
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Rear Louver Mounting Hardware
I have no clue what brand louvers this fits, nor will I speculate. The pictures show it next to a tape measure, to give you an idea of the size. The two pieces are the only pieces that I have. The pieces were on an '88 Camaro, so they are certainly Third Gen.
$35 shipped to 48 states? Shoot me an offer.
$35 shipped to 48 states? Shoot me an offer.
Last edited by two-if-by-sea; Oct 14, 2013 at 05:15 PM.
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
One more, to show the rear
Junior Member
Joined: Jul 2012
Posts: 21
Likes: 0
Car: 1986 z28 camaro
Engine: Chevy sb 305
Transmission: auto, 700r4
Axle/Gears: crap one-wheel wonder
Re: Rear Louver Mounting Hardware
Arent those the ones that go on the bottom? Cause I already have the top hinged ones.
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
I had aluminum Crager louvers 20+ years ago, and they had anchors just like these, made from stainless (I think they are stainless). Plus, there were other parts to those louvers, in addition to these anchors. There were clips on the sides that could be released (to clean the back glass), and the set I had actually had legs on the bottom louver that screwed in; I assume this was to keep them from vibrating. I have no idea if these are Crager anchors.
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
still got 'em...
Trending Topics
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
To the person who sent me an offer last night, I will accept your offer. I tried to respond to your PM, but I get an error message saying that...
...has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her.
Not sure, might be because you are a new member. Send me an email address, and I will communicate with you through that.
...has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her.
Not sure, might be because you are a new member. Send me an email address, and I will communicate with you through that.
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
...still got 'em...
Thread Starter
Joined: Nov 2007
Posts: 683
Likes: 4
From: Mountain Maryland
Car: 89 RS Vert, 89 Formula, 89 Bird
Engine: L03, TBI 350, none
Transmission: 700R4, 700R4, none
Axle/Gears: 3.42, 3.45, none
Re: Rear Louver Mounting Hardware
pm sent
Member
iTrader: (5)
Joined: Apr 2008
Posts: 179
Likes: 5
From: GA
Car: 89 trans am / 67 gto
Engine: 350TPI
Transmission: AUTO
Axle/Gears: 3.27 9 bolt
Re: Rear Louver Mounting Hardware
ill take them.
pm sent.
payment sent.
pm sent.
payment sent.
Last edited by GOATS2QUICK; Oct 14, 2013 at 07:08 AM. Reason: payment.
Thread
Thread Starter
Forum
Replies
Last Post
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
0
Aug 5, 2015 07:57 PM