Wheel studs for Weld Pro Stars?
01-02-2010, 02:26 PM
#1
Member
Thread Starter
iTrader: (4)
Join Date: May 2005
Location: New Waterford, Ohio
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Car: '84 Z28
Engine: 406 sb
Transmission: th400
Axle/Gears: Moser M9/5:14 ratio/Billet Locker
Wheel studs for Weld Pro Stars?
I pulled my rotors off today to repack the bearings and I saw that two studs have been replaced on the pass. side. Although I never had a problem I think it is a good time to replace all the factory studs with longer ARP ones.
Should I use 1/2" or 12mm?
Press in or screw in?
What length?
Open or closed lug nut?
The rear is already done with Moser 3" long 5/8" studs.
Could someone point me in the right direction?
Should I use 1/2" or 12mm?
Press in or screw in?
What length?
Open or closed lug nut?
The rear is already done with Moser 3" long 5/8" studs.
Could someone point me in the right direction?
01-03-2010, 03:26 PM
#2
Member
Thread Starter
iTrader: (4)
Join Date: May 2005
Location: New Waterford, Ohio
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Car: '84 Z28
Engine: 406 sb
Transmission: th400
Axle/Gears: Moser M9/5:14 ratio/Billet Locker
Re: Wheel studs for Weld Pro Stars?
Well... I ordered from Summit Racing today. I hope I got the right ones. I ordered ARP-100-7708. I think they are one inch longer than the factory ones.
01-04-2010, 12:59 AM
#4
Senior Member
Join Date: Aug 2009
Location: Thunder Bay, On, Canada
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8l
Transmission: 700r4
Axle/Gears: Stock
Re: Wheel studs for Weld Pro Stars?
jmd, you told me to buy .769" long shank the other day. I havn't tried them yet, since im not near my car, but I hope they fit.
edit..
yeah.. it said studs. Didn't catch that. I thought it said lug nuts. Well it did but thats not what he was talkin about.
Sorry bout that
edit..
yeah.. it said studs. Didn't catch that. I thought it said lug nuts. Well it did but thats not what he was talkin about.Sorry bout that
Last edited by marekdennhardt; 01-04-2010 at 01:02 AM.
01-04-2010, 01:04 AM
#5
Senior Member
Join Date: Aug 2009
Location: Thunder Bay, On, Canada
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8l
Transmission: 700r4
Axle/Gears: Stock
Re: Wheel studs for Weld Pro Stars?
Hey red, what is the shank legth on your lug nuts? It doesnt matter if its with or without the washer.
thanks
thanks
01-04-2010, 04:05 AM
#6
Member
Thread Starter
iTrader: (4)
Join Date: May 2005
Location: New Waterford, Ohio
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Car: '84 Z28
Engine: 406 sb
Transmission: th400
Axle/Gears: Moser M9/5:14 ratio/Billet Locker
Re: Wheel studs for Weld Pro Stars?
I'm glad I bought the right ones.
lug nuts are 1 1/8" long measured with out washer. Wheels are 1 3/8" thick.
lug nuts are 1 1/8" long measured with out washer. Wheels are 1 3/8" thick.
01-04-2010, 04:10 AM
#7
Senior Member
Join Date: Aug 2009
Location: Thunder Bay, On, Canada
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8l
Transmission: 700r4
Axle/Gears: Stock
Re: Wheel studs for Weld Pro Stars?
Do the center caps for your wheels have a blue center that says weld racing?
Trending Topics
01-04-2010, 05:23 PM
#8
Member
Thread Starter
iTrader: (4)
Join Date: May 2005
Location: New Waterford, Ohio
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Car: '84 Z28
Engine: 406 sb
Transmission: th400
Axle/Gears: Moser M9/5:14 ratio/Billet Locker
Re: Wheel studs for Weld Pro Stars?
I can't remember the color for sure, but they are genuine Weld wheels.
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
7
08-20-2015 09:36 PM
