EPROM Memcal Replacement Question
#1
Member
Thread Starter
Join Date: Oct 2012
Location: Everett, WA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8L v6
EPROM Memcal Replacement Question
I have a question about replacing the factory EPROM in a '165' ecu memcal. I currently have two EEPROM 27SF512 chips. I also have the GP1 Package from Moates. Which allows me to quickly swap chips when I need to burn them. My tune is pretty well dialed in at this point. So I am looking for a more permanent solution since the chip can move a little sometimes and throw a code 51 memcal error. I am looking to solder the chip in to prevent this from happening. Is it possible to remove the factory UV EPROM chip and directly solder the 27SF512 EEPROM chip in its place? To clarify a little I dont mean putting a ZIF socket in place of the factory EPROM I mean soldering the new chip in place of the old. I cant find any posts on the forum directly stating if this is possible or if there is some issue doing it this way. I do know that the G1 adapter exists I would just rather solder the new chip in place of the old on the memcal if possible for easier removal.
What I have now
GP1 Package: http://www.moates.net/gp1-package-gm....html?cPath=64
HDR1 Memcal Header: http://www.moates.net/hdr1-memcal-he....html?cPath=64
165 MAF ECU
What I have now
GP1 Package: http://www.moates.net/gp1-package-gm....html?cPath=64
HDR1 Memcal Header: http://www.moates.net/hdr1-memcal-he....html?cPath=64
165 MAF ECU
#3
Member
Thread Starter
Join Date: Oct 2012
Location: Everett, WA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8L v6
Re: EPROM Memcal Replacement Question
I looked around on moates website and found the d2 28pin DIP socket it was not as easy to find on their website as their other parts. Is this what you are using? It looks like its only $2. This would work for what I am trying to do. Basically rip out the old EPROM and solder the socket to the memcal and solder the legs to the d2 dip socket?
D2 28pin DIP Socket: http://www.moates.net/d2-28pin-dip-s....html?cPath=31
D2 28pin DIP Socket: http://www.moates.net/d2-28pin-dip-s....html?cPath=31
#7
Sponsor
iTrader: (92)
Re: EPROM Memcal Replacement Question
I looked around on moates website and found the d2 28pin DIP socket it was not as easy to find on their website as their other parts. Is this what you are using? It looks like its only $2. This would work for what I am trying to do. Basically rip out the old EPROM and solder the socket to the memcal and solder the legs to the d2 dip socket?
D2 28pin DIP Socket: http://www.moates.net/d2-28pin-dip-s....html?cPath=31
D2 28pin DIP Socket: http://www.moates.net/d2-28pin-dip-s....html?cPath=31
Trending Topics
#8
Member
Thread Starter
Join Date: Oct 2012
Location: Everett, WA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8L v6
Re: EPROM Memcal Replacement Question
Yah I figured I would work out the details when I get it in the mail. I have never used one before. So if I have any questions I will post here.
#10
Member
Thread Starter
Join Date: Oct 2012
Location: Everett, WA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8L v6
Re: EPROM Memcal Replacement Question
Here is my experience soldering a 27SF512 EEPROM directly to the memcal after removing the old EPROM UV chip. Not using any zif sockets or adapters. My ECU does work after replacing the chip with this method. My soldering is not very good but you should get the concept. Remember to pay special attention to making sure your soldering does not bridge any of the legs.
1st: I cut the legs of the EPROM and removed the chip
2nd: I cut the legs of the chip flush with the plastic of the memcal. Do not pull on the original EPROM when you have cut most of the legs just be careful and cut the legs.
3rd: Bend the remaining portion of the legs down in the plastic of the memcal with a small screwdriver
4th: Make sure you position the chip in the right direction illustrated by tuned performance earlier in the thread.
5th: Be gentle and push in the new 27SF512 chip into the memcal and make sure all legs are seated properly.
6th: Get out a small soldering iron and solder in each leg. You need very little solder for each of the legs. If you use to much your going to have issues bridging two legs together.
7th: Put it in your ECU and test.
EPROM Removed, Legs Cut Flush, and Pushed Down in Memcal
27SF512 EEPROM Pushed into Memcal Not Soldered
New 27SF512 EEPROM Soldered Into Memcal
1st: I cut the legs of the EPROM and removed the chip
2nd: I cut the legs of the chip flush with the plastic of the memcal. Do not pull on the original EPROM when you have cut most of the legs just be careful and cut the legs.
3rd: Bend the remaining portion of the legs down in the plastic of the memcal with a small screwdriver
4th: Make sure you position the chip in the right direction illustrated by tuned performance earlier in the thread.
5th: Be gentle and push in the new 27SF512 chip into the memcal and make sure all legs are seated properly.
6th: Get out a small soldering iron and solder in each leg. You need very little solder for each of the legs. If you use to much your going to have issues bridging two legs together.
7th: Put it in your ECU and test.
EPROM Removed, Legs Cut Flush, and Pushed Down in Memcal
27SF512 EEPROM Pushed into Memcal Not Soldered
New 27SF512 EEPROM Soldered Into Memcal
#11
Sponsor
iTrader: (92)
Re: EPROM Memcal Replacement Question
To remove the soldered in prom . Pry in the prom and press your soldering iron down on each leg. This breaks the solder joint. I have never left the legs ion the memcal they seem to come out with the prom.
you might have to repeat the prying up process a few times but it comes out complete.
I just prefer the zif Incase the eeprom fails. I have had a couple duds from moates.
It looks like your soldering iron maybe your wasn’t getting hot enough. I use mine at 550f.
you might have to repeat the prying up process a few times but it comes out complete.
I just prefer the zif Incase the eeprom fails. I have had a couple duds from moates.
It looks like your soldering iron maybe your wasn’t getting hot enough. I use mine at 550f.
Last edited by Tuned Performance; 04-02-2019 at 02:41 PM.
#12
Supreme Member
iTrader: (1)
Re: EPROM Memcal Replacement Question
I actually like these better than the Moates version:
https://www.ebay.com/itm/GM-MEM-CAL-...-/112553592450
GD
https://www.ebay.com/itm/GM-MEM-CAL-...-/112553592450
GD
#13
Sponsor
iTrader: (92)
Re: EPROM Memcal Replacement Question
I’ll sell you one lol
https://www.thirdgen.org/forums/engi...k-adapter.html
https://www.thirdgen.org/forums/engi...k-adapter.html
#14
Supreme Member
iTrader: (1)
Re: EPROM Memcal Replacement Question
If I needed one.... I have extra at this point since I went EBL with my personal car. But I did use one daily for a year or so without problems. The low profile ZIF seemed to work well and take up less space than the Moates version.
GD
GD
#15
Member
Thread Starter
Join Date: Oct 2012
Location: Everett, WA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8L v6
Re: EPROM Memcal Replacement Question
My soldering iron is just a very cheap one but it has a fine tip. I have a better quality one but its much larger. As long as it works is all I am worried about at the moment. Honestly it was not as hard as I thought it would have been so overall I am happy.
#16
Junior Member
Re: EPROM Memcal Replacement Question
i need some help with a prom for a 1992 pontiac trans am 5.0l
PROM DELCO AXXB 3063
any info would be helpfull
looking for new old stock if possible
but ideas anything would help
PROM DELCO AXXB 3063
any info would be helpfull
looking for new old stock if possible
but ideas anything would help
#20
Junior Member
Re: EPROM Memcal Replacement Question
is it new or used or just old new in the box???
i was looking at it and its listed used?
i was looking at it and its listed used?
#22
Supreme Member
iTrader: (1)
Re: EPROM Memcal Replacement Question
Tuned Performance is a very reputable member and ebay seller - if he says it's good you can bet on it, and I'm quite positive he will stand behind it also.
GD
Thread
Thread Starter
Forum
Replies
Last Post