TPI Induction/Intake setup for sale!!!
02-08-2008, 09:14 AM
#1
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: United States
Posts: 2,078
Likes: 0
Received 0 Likes
on
0 Posts
TPI Induction/Intake setup for sale!!!
I have for sale an induction setup for 87+ LB9 L98 305-350 engines. What is included is the following:
TPI Edelbrock Intake Manifold-Cast aluminum (Retail is $399.00)
Holley Billet Air foil($59.99)
Billet Adustable Fuel Pressure Regulator($69.99)
8 SVO 19# injectors($205.00)
Rebuilt stock 48mm Throttle Body
Stock Intake Runners
Ported Plennum
Stock Fuel Rail w/ 9th injector cold start
Brand New Remanufactured Distributor w/ Internal Ignition Module($174.99)
I guarantee on all parts in excellent working order. All together parts run over $850.00. I'm not expecting that much and would realistically like to get $400.00 for everything. If you have any questions feel free to ask. My zip code is 11356. Thanks
TPI Edelbrock Intake Manifold-Cast aluminum (Retail is $399.00)
Holley Billet Air foil($59.99)
Billet Adustable Fuel Pressure Regulator($69.99)
8 SVO 19# injectors($205.00)
Rebuilt stock 48mm Throttle Body
Stock Intake Runners
Ported Plennum
Stock Fuel Rail w/ 9th injector cold start
Brand New Remanufactured Distributor w/ Internal Ignition Module($174.99)
I guarantee on all parts in excellent working order. All together parts run over $850.00. I'm not expecting that much and would realistically like to get $400.00 for everything. If you have any questions feel free to ask. My zip code is 11356. Thanks
02-08-2008, 03:54 PM
#2
Supreme Member
iTrader: (2)
Join Date: Nov 1999
Location: Monroe,NC
Posts: 1,779
Likes: 0
Received 20 Likes
on
15 Posts
Car: 90 Formula
Engine: 305
Transmission: 700R4
Axle/Gears: 9 bolt/3.27
Re: TPI Induction/Intake setup for sale!!!
Would you be willing to part the setup? I'm interested in the Edelbrock manifold.
02-08-2008, 11:22 PM
#5
Member
Join Date: Jul 2007
Location: Michigan
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2007 Cobalt LT
Engine: M62'd 2.2L L61
Transmission: 4T45E 4-speed Automatic
Axle/Gears: Stock
Re: TPI Induction/Intake setup for sale!!!
Do you happen to have the PCV breather setup still laying around?
Trending Topics
02-09-2008, 10:24 AM
#8
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: United States
Posts: 2,078
Likes: 0
Received 0 Likes
on
0 Posts
Re: TPI Induction/Intake setup for sale!!!
If someone takes the whole setup, i'll include a practically new Walbro Electric internal pump. Has about 10 minutes worth of use and is in excellent condition.
This is a picture of the intake when it was mounted on the car. Still looks the same. Everything else is gone.
This is a picture of the intake when it was mounted on the car. Still looks the same. Everything else is gone.
Last edited by vortech305; 02-09-2008 at 10:41 AM.
02-10-2008, 06:45 AM
#11
Member
Join Date: Nov 2007
Location: Leavenworth, Kansas
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Trans Am
Engine: 305 TPI (for now)
Transmission: 700-R4 (for now)
Axle/Gears: 2.73 10 bolt (for now)
Re: TPI Induction/Intake setup for sale!!!
very interested. what kind of performance do you think could be expected with my current setup? it's in the signature.
02-10-2008, 10:44 AM
#14
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: United States
Posts: 2,078
Likes: 0
Received 0 Likes
on
0 Posts
Re: TPI Induction/Intake setup for sale!!!
Someone asked the same and i thought it was possible to fit with some angle work, but i hear it's too much of a hassle. Unless your good with machining. The intake has plenty of meat to portmatch for serious aftermarket heads. The stock base intakes are thin and wont allow much porting. So to answer your questions, i believe these are just for standard 87+ sbc.
Thread
Thread Starter
Forum
Replies
Last Post
evilstuie
Tech / General Engine
22
01-09-2020 08:29 PM
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
08-12-2015 03:41 PM