Iroc build
#1
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Iroc build
Going to try and start a build thread. I will try and keep updated. Back story, car was had a 406 Tpi, t56, 150 shot, and a 10 bolt. Tore it apart about five years ago unhappy with the combo. Car got back burnered while I was building my shop. Took some steps this summer to finish it. Setup will be following
-5.3 ls with ls6 heads, katec ls6 torque cam, arp hardware
-4l80 built with rossler trans brake and custom ati converter
-VS racing billet 80mm turbo, eBay air to water, chiseled water tank
-Quick performance 9 inch with a spool and 3.55 gear.
I am running an aei motor plate and mid plate if any one is curious on the brand. Would highly recommend if going this direction.
-5.3 ls with ls6 heads, katec ls6 torque cam, arp hardware
-4l80 built with rossler trans brake and custom ati converter
-VS racing billet 80mm turbo, eBay air to water, chiseled water tank
-Quick performance 9 inch with a spool and 3.55 gear.
I am running an aei motor plate and mid plate if any one is curious on the brand. Would highly recommend if going this direction.
Last edited by grover85; 11-26-2017 at 12:25 PM.
#2
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Re: Iroc build
Got the rack mounted and rear suspension fab work done. Break down of parts
Rear
-Quick performance 9 inch
-Trz anti roll bar
-Moddified Bmr torque arm
-Founders rear coil overs with 110lbs springs
-Control arms are mine built with rod ends
Front
-Lakewood struts
-Coil over
-Founders strut mounts
-PA racing k member
Rear
-Quick performance 9 inch
-Trz anti roll bar
-Moddified Bmr torque arm
-Founders rear coil overs with 110lbs springs
-Control arms are mine built with rod ends
Front
-Lakewood struts
-Coil over
-Founders strut mounts
-PA racing k member
Last edited by grover85; 11-25-2017 at 11:16 PM.
#4
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Re: Iroc build
The next big step was sending it to someone who is a much better welder and fabricator then I am. So enjoy the pics
#7
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Re: Iroc build
Last ones of me picking it up to bring home. Have more fab work to do before I blow it apart to paint and reassemble.
Trending Topics
#10
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Re: Iroc build
I wanted full exhaust and just couldn’t settle on fender dump. For my set up the 4 inch was difficult. Tony the person fabricating it said dual 3 might have been easier. All in all I am happy how it turned out.
#12
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2003
Location: New Germany, MN
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc
Engine: 5.3
Transmission: 4L80E
Axle/Gears: 9 Inch w/ 3.55
Re: Iroc build
I have my old 4 inch that has dual tail pipes and muflex muffler that I could sell you if your interested.