Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: Ronny
Showing results 1 to 50 of 498
Search took 0.24 seconds.
Forum: DIY PROM
07-28-2021, 12:55 PM
Replies: 7
Views: 325
Posted By Ronny

Re: anyone have a dead LSU 4.9 O2 sensor?

I have a brand new one I purchased in error. Seller will not allow me to return..
Forum: DIY PROM
07-20-2021, 10:36 AM
Replies: 3
Views: 232
Posted By Ronny

Re: anomaly WU dalalogs

Innovate automatically sets at that V by user selecting fuel in use. In my case E10. Stoich is reported at 14.7/1 or 1.0 Lambda,
Forum: DIY PROM
06-15-2021, 02:23 PM
Replies: 1
Views: 286
Posted By Ronny

What did I do wrong?

I did a VE Learn today and when I open the new .bin all I get t.in TP is a gray blank screen with no data. I shows the .bin name and XDF. I am using EBL_40.XDF..Any prior .bin I open is same result.
Forum: DIY PROM
06-15-2021, 01:51 PM
Replies: 3
Views: 232
Posted By Ronny

Re: anomaly WU dalalogs

Thanks. I will did up owners manual....
Forum: DIY PROM
06-15-2021, 09:50 AM
Replies: 3
Views: 232
Posted By Ronny

anomaly WU dalalogs

I had my Innovate WB reporting to its software in controller and to pillar gauge. I recall them showing the same data as far as A/F.

I then patched into EBL-WU and I do not recall then reporting...
Forum: DIY PROM
04-02-2021, 07:05 PM
Replies: 3
Views: 476
Posted By Ronny

Re: CL based upon RPM (EBL)

I turned the NB off. I am using WB reporting data A/F to logs but not using WB in place of NB. Problem is over cept if weather gets real warm. Did logs at 50d F. I have reached a point where...
Forum: TBI
03-09-2021, 11:57 AM
Replies: 7
Views: 1,285
Posted By Ronny

Re: 305 tbi to 350 tbi questions

possibly the distributor is 180 degrees out
Forum: DIY PROM
01-23-2021, 12:43 PM
Replies: 3
Views: 476
Posted By Ronny

CL based upon RPM (EBL)

I just completed a year of tuning my 396SB with cam236/2442 @.05 112 LSA. Seems I was chasing my tail initially. With convectional driving it continually added fuel per dalaogs. It was taking out...
Forum: TBI
12-10-2020, 02:55 PM
Replies: 24
Views: 20,429
Posted By Ronny

Re: Crossfire Tech - Both TBs share single IAC mod - HOW-TO with photos

I replaced my original CF fuel pump with a TPI pump.

I now have a Accel high pressure pump since now is a 396 SB port fuel with single plane. I have the TPI pump that I could sell to you. It is 5...
Forum: TBI
03-04-2020, 08:40 AM
Replies: 119
Views: 48,347
Posted By Ronny

Re: crossfire renegade intake manifold?

An inexpensive alternative to the CF manifold is a single plane weiand(spell?) accelerator with adapter plate to a 7.4L TB. Or a edelbrock torker with same. Those are low profile manifolds that may...
Forum: DIY PROM
03-02-2020, 05:06 PM
Replies: 6
Views: 455
Posted By Ronny

Re: question on my new tune?

Just spoke to Innovate. They say odds are good the NB sensor is kaput. I asked how serious racers can monitor A/F with race gas. they say they replace them every other run ! OK thanks to DR. It...
Forum: DIY PROM
03-02-2020, 04:27 PM
Replies: 6
Views: 455
Posted By Ronny

Re: question on my new tune?

I am a bit surprised that Innovate WB sensor would be corrupted by race fuel(lead). Maybe it is designed to use passenger car WB that is E10-E85. Now I see on market a specific devise that will...
Forum: DIY PROM
03-02-2020, 04:23 PM
Replies: 6
Views: 455
Posted By Ronny

Re: question on my new tune?

see attachment: datalog
Forum: DIY PROM
03-02-2020, 08:26 AM
Replies: 6
Views: 455
Posted By Ronny

Re: question on my new tune?

Hydraulic roller. The cam is 234 intake and 242 ext.@ .05. LSA is 112. lift is .628 int and .611 ext. This is a street driven engine. Cam was picked out by Comp Cams tech line rather than me...
Forum: DIY PROM
03-01-2020, 02:28 PM
Replies: 6
Views: 455
Posted By Ronny

question on my new tune?

Installed aa new 396 SB this past summer. Running EBL
Set BPC to 174 for 24 lbs injectors at 43 lbs FP. I realize I need stronger fuel pump and larger injectors that is coming soon
Broke in...
Forum: TBI
02-06-2020, 02:39 PM
Replies: 64
Views: 60,070
Posted By Ronny

Re: Who is atually using a GM 454 TBI unit on a SBC?

When I switched from Holley TBI manifold/7.4L TB/ 75 LB injectors to port fuel the PF setup ran so much better. I will say it may have been transport delay or the fuel coming in late vs the air. ...
Forum: Alternative Port EFI Intakes
01-12-2020, 11:35 AM
Replies: 13
Views: 10,425
Posted By Ronny

Re: Edelbrock Pro Flo XT

The dimensions are on Edel website. I run a Vic Jr SP manifold with a 1000cfm Edel TB. I believe that may be the Pro Flow package. I however run an after market ECU(Dynamic EFI/EBL). With a 2...
Forum: Power Adders
12-02-2019, 05:26 PM
Replies: 30
Views: 34,066
Posted By Ronny

Re: Can you blow thru a TBI with success?

WOW this is an old thread…. If we are using a 7.4L TB and then equip it with 75LB inj's and run max FP still it may (will) have have insufficient fuel. AKA LEAN. You will need a fuel pump that...
Forum: DIY PROM
08-26-2019, 04:49 PM
Replies: 8
Views: 4,009
Posted By Ronny

Re: IAT sensor to EBL-ECU Q

I Believe it was 21. I recall sending the ECU back to RBob and he marked on the pin board where I should place the lead into the EBL/ECU. It, the EBL has worked flawlessly for past many years. But...
Forum: DIY PROM
06-18-2019, 09:08 AM
Replies: 4
Views: 3,713
Posted By Ronny

Re: ? on crank values

Thank you for your input. I think I may have discovered my error. I think the 3006 .bin is OK with stock values. As I stated the Aero VAFPR may have caused the enrichment issue during break in. ...
Forum: DIY PROM
06-11-2019, 12:56 PM
Replies: 4
Views: 3,713
Posted By Ronny

Re: ? on crank values

my error. What I stated was from a bin I made march 2019. The 3006 has crank afr at 8.0 scaling down to .8. I went back to stock values of 2006. I will reflash tomorrow morning.
Forum: DIY PROM
06-11-2019, 08:21 AM
Replies: 4
Views: 3,713
Posted By Ronny

? on crank values

During break in of new motor (396 SB) we fouled the plugs due to overly rich tune since it was using much higher map values than prior motor/tune. I believe it was caused by my VAFPR not seeing lower...
Forum: Brakes
03-30-2019, 09:15 AM
Replies: 2
Views: 2,627
Posted By Ronny

Re: brakes brakes brakes!

Issue was brakes at 50% due to lack of vac caused by cam. Should be 16 inches of vac and it is at 10 inches. I added a vac vane pump and hooked it to brake booster. It worked well. The vac fed...
Forum: DIY PROM
03-29-2019, 10:28 AM
Replies: 5
Views: 490
Posted By Ronny

Re: EBL malf flags

Sorry about that. I should have checked the log first. I see that was about a 15 minute ride at 30-45 mph. I don't recall that ride setting off a CE. However I did a 24 mile ride on XWay at 65...
Forum: Brakes
03-29-2019, 07:48 AM
Replies: 1
Views: 421
Posted By Ronny

Brakes vac pump question.

I instald one due to 10 in of vac on new motor and cam. 236/242 @.05 112 lsa and 396 SB. I was told I need a check valve installed. Pump is in and works s well. pulls 16-20. How is valve plumbed...
Forum: DIY PROM
03-28-2019, 08:09 PM
Replies: 5
Views: 490
Posted By Ronny

Re: EBL malf flags

I sent a data log to RBob at dynamic efi. Could not attach here.

FYI Map was seeing 10 inches per my vac gauge. That is why I added the vac pump. I found out how I need to replumb the pump with a...
Forum: DIY PROM
03-26-2019, 01:28 PM
Replies: 5
Views: 490
Posted By Ronny

Re: EBL malf flags

I can do that. I did not mention but I needed to add a vacuum pump due to significant loss of vac and resulting braking was noticeably lessened to a point where it was unsafe,,It appears in logs...
Forum: DIY PROM
03-26-2019, 10:36 AM
Replies: 5
Views: 490
Posted By Ronny

EBL malf flags

I am getting a MAP flag in my data log and occasionally a CE light on dash. Happens on an extended cruise at 60 MPH. Does not occur at 40 MPH or less. Car runs well on tune. It is due to my cam...
Forum: DIY PROM
03-23-2019, 03:31 PM
Replies: 1
Views: 494
Posted By Ronny

coolant sensors

There are three I believe. One for fan control, another for gauge and another I am not certain but I presume is data to ECU. Two are at head(driver/passenger) and the third is at thermostat. I am...
Forum: Alternative Port EFI Intakes
12-23-2018, 01:05 PM
Replies: 3
Views: 581
Posted By Ronny

Re: vacuum booster needed

There is little room under the hood of a C4. It looks like it will go in one of two compartments (10"x 10" x 10") behind seats.
Forum: Alternative Port EFI Intakes
12-22-2018, 10:14 AM
Replies: 3
Views: 581
Posted By Ronny

vacuum booster needed

am posting this here since I believe you guys have more experience with higher HP motors. I just replaced my 350 with a 396 stroker. Picked up car from my mechanics(friends) shop when completed and I...
Forum: DIY PROM
12-13-2018, 09:09 AM
Replies: 8
Views: 747
Posted By Ronny

Re: First ride on new engine/tune

Yes...
Forum: DIY PROM
12-12-2018, 02:12 PM
Replies: 8
Views: 747
Posted By Ronny

Re: First ride on new engine/tune

OK.... I think have a reason for the significant enrichment I experienced. On setting the initial timing and 10 minute break in after I had a datalog running showing rich on BLM and WB and exhaust...
Forum: DIY PROM
11-29-2018, 10:36 AM
Replies: 8
Views: 747
Posted By Ronny

Re: First ride on new engine/tune

Dom: I know that. I was just trying to be humorous.....OBTW too much power for a crossfire, a 396 is anyway. Only drove it 30 miles so far.
Forum: DIY PROM
11-29-2018, 09:14 AM
Replies: 8
Views: 747
Posted By Ronny

Re: First ride on new engine/tune

Hi Dom...."common man throw me a bone"

Yea I changed the BPC for a 396. 24 lb injectors at 43 lbs fp. Oddly enough it was pig rich. I should have checked the vac line from the Aero VAFPR but...
Forum: DIY PROM
11-27-2018, 09:13 AM
Replies: 6
Views: 1,125
Posted By Ronny

Re: Speedo recalibration Question.

I bought the Dakota Digital unit. The directions could be better. I wont hook it up till Spring. Trying to get educated on this over winter.
Thank you.
Forum: DIY PROM
11-26-2018, 09:24 AM
Replies: 6
Views: 1,125
Posted By Ronny

Re: Speedo recalibration Question.

Thank you!
Forum: DIY PROM
11-25-2018, 01:57 PM
Replies: 6
Views: 1,125
Posted By Ronny

Speedo recalibration Question.

This may be in wrong Forum?

1984 C4.

Replaced the 4+3 with a Tremec TKO 600 that I need to calibrate speedo with a Dakota Digital signal interface unit.

My options are to recalibrate a...
Forum: DIY PROM
11-25-2018, 01:28 PM
Replies: 8
Views: 747
Posted By Ronny

First ride on new engine/tune

On break in I was seeing BLM at 108 and WB 02 reads at 13.0-13.4 in closed loop. Idle A/F same. Old engine was 350 and new engine 396. I changed only the BPC to 173. It fouled the nitrous plugs....
Forum: DIY PROM
11-15-2018, 08:55 AM
Replies: 5,154
Views: 633,750
Posted By Ronny

Re: Tuning with the EBL

A couple of items to help if the idle is wandering./erratic.

Lock SA for idle. Set flag Add some SA a little at a time and see if that helps.

Place same values for VE table around the rpm/map...
Forum: DIY PROM
11-13-2018, 04:58 PM
Replies: 5,154
Views: 633,750
Posted By Ronny

Re: Tuning with the EBL

BLM/INT can add/subtract about 25% of fuel for changing conditions(barometric, temp/wear).So a morning temp of say 32dF and afternoon 60dF can be handled nicely as can -15dF vs 100d F. Seems like...
Forum: DIY PROM
11-13-2018, 08:34 AM
Replies: 5,154
Views: 633,750
Posted By Ronny

Re: Tuning with the EBL

I would use the stock GM IAC tables . I bet you are using 3006 from RBob. I am. With OL as you know there is no INT/BLM correction. If you are rich I would start with pulling fuel from the two...
Forum: DIY PROM
11-07-2018, 10:06 AM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

First datalog after setting the distributor and timing:

10 sec into log A/F 10.5/1. NB 02 (heated) swings are from .450-460.

2 min into log A/F is 13.7 NB shows 400-700 swing.

MAP is 72. Car...
Forum: DIY PROM
11-06-2018, 08:38 AM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

I see in 3006 that 02 Idle 02 terms has Lean at 569 Rich at 599 and Mean R/L at 599. Why Rich and Mean the same?
I edited....
Forum: DIY PROM
11-05-2018, 05:55 PM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

It looks like I have the 3006 values in my current bin. I only changed the BPC B4 we fired it up. I used your utility. The reported A/F from WB showed rich in CL however the coolant was 140F and...
Forum: DIY PROM
11-05-2018, 05:37 PM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

Thank you!
Forum: DIY PROM
11-05-2018, 02:01 PM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

I find that when I use compare function in TP it puts zeros in the compare bin. I was using my bin as compare. If I reverse and put the 3006(EBL bin) as compare it does same placing zeros in 3006. ...
Forum: DIY PROM
11-05-2018, 01:42 PM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

I cannot find that in 3006? I found only one item that relates to MAP. It is INT-Mean R/L. Map 100 is 521 mv and MAP 20 is 572. My port fuel .bin shows values ZERO's ! That cant be correct? ...
Forum: DIY PROM
11-05-2018, 12:25 PM
Replies: 12
Views: 782
Posted By Ronny

Re: What is the item in TP?

Thanks again....
Forum: DIY PROM
11-05-2018, 09:35 AM
Replies: 12
Views: 782
Posted By Ronny

What is the item in TP?

I data logged my new 396 CID SB stroker for the first time last week. I see in WU my A/F is 13.1 to 13.3 in CL. I believe it should be 14.1 for E10 fuel. I believe the WB is calibrated correctly...
Showing results 1 to 50 of 498
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 06:59 AM.