ttypecamaro

iTrader: (2)

My brother spun a rod bearing in his 88 2.8 firebird with only 50K miles on it. the rear main seal leaked about a quart of oil per tank of gas since he got the car, and he let it get way too low on oil. I'm selling his turbo kit to pay for rebuilding the motor.

check out the turbo kit for sale

https://www.thirdgen.org/forums/engi...turbo-kit.html

The question is... is it true that I can just get a 3.1L rotating assembly and put it in the 2.8 block? I'm pretty sure a 3rd gen 3.1L rotating assembly will work, but what about a 3.1 from a newer car with the magnetic ignition (no distributor). Its hard to justify getting it from the junkyard though, only to find out its worse off than your spun bearing motor. with only 50K on the motor, everything still looks new inside. it always had the oil changed ontime, and fresh oil was constantly being added. it was my grandmother's car.

I'm also looking for a power steering pump bracket, I found it broken when I was taking everything apart.

daves12secV6

iTrader: (3)

hey man i can show u were to buy a new crank and rod(s) for under 100 $'s

i fu can wait a few hours ill give ya the links
u can install a 3.1 crank but u have to swap th epistions to 3.1 pistions, u can buy brand ne whyperectics on ebay for under 50$;s

cooltc2004

iTrader: (4)

Sent you a PM

ttypecamaro

iTrader: (2)

cool I'd like to see those links, thanks for looking out.

daves12secV6

iTrader: (3)

http://cgi.ebay.com/ebaymotors/GM-CH...QQcmdZViewItem
^^ its not new
there were about 4 brand new cranks on ebay for 75$ buy it now but i cant seem to find them
and brand new 44$ pistions for u to use the 3.1 crank
http://cgi.ebay.com/ebaymotors/GM-CH...QQcmdZViewItem
std size .50 and 1mm over bore sizes u
connecting rods 15$'s
though im unsure if it a set of 6 or if its 15$'s per rod,though u prolly only need one rod
http://cgi.ebay.com/ebaymotors/CONNE...92693809QQrdZ1

daves12secV6

iTrader: (3)

just remeberd i have a used set of stock 3.1 pistons if u want them, just pay shipping on them

daves12secV6

iTrader: (3)

http://cgi.ebay.com/CHEVY-3-1-191-V6...QQcmdZViewItem
^^ correct link for the pistons
opps after relooking at the ebay ad for the pistons they only have the .50mm oversized left. though if u look around a bit there are other piston sets on ebay

ttypecamaro

iTrader: (2)

are the rods the same for the 2.8 and 3.1 motors?

daves12secV6

iTrader: (3)

yes 2.8/3.1/3.4 all use the same rods
2.8/3.1 is the same block

ttypecamaro

iTrader: (2)

thanks.
So all I (my bro) need is a 3.1 crank, 1 rod, a 3.1 master rebuild kit (w/ pistons)? What about a 3.1 harmonic balancer and flexplate? Or are they the same too?

daves12secV6

iTrader: (3)

yeah pretty much if u piece it together on ebay u can prolly do it very cheap.

btw what blow off valve do u have ???

ttypecamaro

iTrader: (2)

I don't have a BOV on it, but I could slap an ebay reversion style unit on there pretty easily. weld a bung/flange near the TB and revert it in front of the turbo.

I've used two other ebay BOVs on V8 setups that worked fine except requiring lubrication every couple months.

ttypecamaro

iTrader: (2)

my brother ordered a reman 3.1 crank. He needs to order a rebuild kit, and a rod. The last thing he needs is a cam. In an attempt to avoid too many tuning issues, I told him to buy something that claims to be computer compatible. This motor probably won't be turboed in the near future anyway... he just needs to get back and forth to highschool for now.

What is the approximate max lift on stock heads/springs? Can larger valves be bought/installed in the heads? I was considering a cam 212/212 .440"/.440" then putting some 1.6 rockers on it (putting up to .469"/.469")

daves12secV6

iTrader: (3)

hey call up delta cams and order a regrind they will gind u the compcams 260 cam with new lifters for 100$'s, a belive it was stated that a new cam was 125$ for any specs u wanted

ttypecamaro

iTrader: (2)

Northern Auto Parts sells a complete rebuild kit with Speed-Pro Hypereutectic pistons...

Federal Mogul Rings
Federal Mogul recessed head Pistons
Federal Mogul Rod Brgs
Federal Mogul Main Brgs
Clevite Cam Brgs
Melling Oil Pump
Federal Mogul Camshaft
Federal Mogul Lifters
Melling Timing Components
Pioneer Frost Plugs
Victor Gaskets

They gave me a credit of like $30 towards a different cam when I bought my 350 rebuild kit from them. If they do that for my brother he should get the comp260H for $95.

firstfirebird

iTrader: (3)

That is basically the same cam I got from Delat for $100 w/lifters, IMHO is a good deal.

ttypecamaro

iTrader: (2)

My brother ended up getting the cam custom ground through who ever Northern auto parts uses/contracts for $80. This car should be interesting to drive.

daves12secV6

iTrader: (3)

still gonna be turbo?

ttypecamaro

iTrader: (2)

since I repo'd his turbo kit, probably not, unless he can come up with the money to buy it back. otherwise, I'll wait till he can get the money for a new kit.