Car Audio Car audio related questions and helpful hints for building the best sound system for your car or getting the most out of what you have.

sub w/ Profie amp

Thread Tools
 
Search this Thread
 
Old Jan 14, 2003 | 09:55 PM
  #1  
Sunny RS's Avatar
Thread Starter
Member
20 Year Member
 
Joined: Jun 2002
Posts: 182
Likes: 0
From: Anoka MN
Car: 89' RS
Engine: 5.0
Transmission: slipping 700r4, soon probuilt
sub w/ Profie amp

I want to get a 10" or 12" dual voice coil. For the time being I want to run it off my Profile Clarus 600 Cl which gives out 150x2 RMS. any ideas of what sub i should get for around $120? I was looking at Rockford, Alpine and Kicker but cant really decide.
Reply
Old Jan 19, 2003 | 05:27 PM
  #2  
Huckster's '84 TA's Avatar
Member
 
Joined: Feb 2001
Posts: 265
Likes: 0
From: Austin, Texas
Car: 1984 Pontiac Trans Am
Engine: 5.0L
Transmission: TH700-R4
why do you want a DVC?

you could try the Kicker Comps, RF HE2, or the MTX 6000's
Reply
Old Jan 20, 2003 | 11:31 AM
  #3  
Jim85IROC's Avatar
TGO Supporter
iTrader: (2)
 
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
What do you want out of your subs, SPL, sound quality, or a mixture of both? How much room do you have to play with? This sort of stuff matters.

I'd look into Elemental Designs or Adire as well as the other brands you mentioned. Unfortunately, these brands are more or less purchased directly, so you won't have a chance to audition them.
Reply
Old Jan 20, 2003 | 01:46 PM
  #4  
Sunny RS's Avatar
Thread Starter
Member
20 Year Member
 
Joined: Jun 2002
Posts: 182
Likes: 0
From: Anoka MN
Car: 89' RS
Engine: 5.0
Transmission: slipping 700r4, soon probuilt
I would like sound quality over spl but good balance of both. thanx
Reply
Old Jan 21, 2003 | 09:46 AM
  #5  
Jim85IROC's Avatar
TGO Supporter
iTrader: (2)
 
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
Then I'd look into Adire, Resonant Engineering, Audiomobile, Elemental Designs, etc. All of them offer affordable drivers that should work very well. You can get 12" Shivas for $125 shipped, which might be one of the best deals in car audio.
Reply
Old Jan 21, 2003 | 11:17 AM
  #6  
White Ninja's Avatar
Member
 
Joined: Jan 2002
Posts: 470
Likes: 0
From: Yardville, New Jersey
First - running the right channel to one VC and left to the other is discouraged, i heard this could cause damage.

second - you might also want to look out, Running 1 sub, i take it you're going to bridge the amp. most amps won't run, and i know for a fact, the Profile won't run Bridged at less than 4 ohms, so....DVC might be tough. a SVC 4ohm would be your best bet. I'm not sure what the Shiva's are that were mentioned, but keep that in mind.

- Andy

Last edited by White Ninja; Jan 21, 2003 at 11:20 AM.
Reply
Old Jan 21, 2003 | 02:36 PM
  #7  
Jim85IROC's Avatar
TGO Supporter
iTrader: (2)
 
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
A lot of DVC subs have dual 2-ohm coils, so you can just series-wire them and get a safe impedance.
Reply
Old Jan 21, 2003 | 02:58 PM
  #8  
White Ninja's Avatar
Member
 
Joined: Jan 2002
Posts: 470
Likes: 0
From: Yardville, New Jersey
true
Reply
Old Jan 27, 2003 | 06:03 PM
  #9  
Sunny RS's Avatar
Thread Starter
Member
20 Year Member
 
Joined: Jun 2002
Posts: 182
Likes: 0
From: Anoka MN
Car: 89' RS
Engine: 5.0
Transmission: slipping 700r4, soon probuilt
what are these shivas and were can i get them?
Reply
Old Jan 27, 2003 | 06:32 PM
  #10  
mudaholic's Avatar
Senior Member
 
Joined: Nov 2001
Posts: 771
Likes: 0
From: Seattle, WA
adireaudio.com .. i believe ampmanaudio.com sells them too
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Cam-aro
Camaros Wanted
2
Nov 12, 2015 03:35 PM
SRKLEGIN
Interior
7
Oct 29, 2015 06:38 PM
oil pan 4
Fabrication
2
Oct 6, 2015 11:56 AM
SRKLEGIN
Interior
6
Oct 3, 2015 10:11 PM
raymondandretti
Electronics
1
Sep 27, 2015 06:43 PM




All times are GMT -5. The time now is 07:44 PM.