Cooling Discuss all of the aspects of cooling that you can think of! Radiators, transmissions, electric fans, etc.

Temp Sending Unit Problem

Old Mar 14, 2008 | 04:26 PM
  #1  
leek157's Avatar
Thread Starter
Member
 
Joined: Jul 2007
Posts: 149
Likes: 0
From: Lisle Illinois
Car: 95 SHO. 87 IROC red 69 Vette blue
Engine: 3.0 Yamahammer.5.7 TPI L98, 350
Transmission: mtx4 ,700r4, 4speed,
Axle/Gears: 3.27, 3.73
Temp Sending Unit Problem

Hi, my temp gauge stoped working from what I understand is that the temp sending unit is bad, I know it is located on the left side cylinder head somewhere between #1&3 cylinders but I cannot find it and Im not sure exactly what it looks like. Any help and or pictures would be greatly appreciated.
Reply
Old Mar 14, 2008 | 06:04 PM
  #2  
CRUSHER's Avatar
Junior Member
 
Joined: Apr 2002
Posts: 99
Likes: 0
From: Toronto
Car: 88 Iroc
Engine: 350(300hp G.M crate, supercharged)
Transmission: 700R4
Re: Temp Sending Unit Problem

Could be a few things...Check your actual gauge in the car first, could be bad..Check the wire connected to the sending unit is not loose...I had that problem once, my gauge would not read..reconnected the wire and bam she worked again....Was a loose connection
Reply
Old Mar 14, 2008 | 06:59 PM
  #3  
UnderCover89TBI's Avatar
Supreme Member
iTrader: (25)
 
Joined: Feb 2006
Posts: 7,260
Likes: 5
From: Manteca,California. Nor Cal.
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Temp Sending Unit Problem

#1 and #3 cylinder are on drivers side of vehicle, thier is only one sensor/sending unit there..should be pretty easy to see...
Reply
Old Mar 14, 2008 | 10:26 PM
  #4  
IROCmonkey's Avatar
Senior Member
 
Joined: Jun 2002
Posts: 687
Likes: 0
From: Tampa Bay, FL
Car: 85 IROC
Engine: LB9
Transmission: 700R4
Axle/Gears: 3.42
Re: Temp Sending Unit Problem

usually looks like this

http://www.partsamerica.com/product_.../ts26471-1.jpg
Reply
Old Mar 14, 2008 | 11:10 PM
  #5  
leek157's Avatar
Thread Starter
Member
 
Joined: Jul 2007
Posts: 149
Likes: 0
From: Lisle Illinois
Car: 95 SHO. 87 IROC red 69 Vette blue
Engine: 3.0 Yamahammer.5.7 TPI L98, 350
Transmission: mtx4 ,700r4, 4speed,
Axle/Gears: 3.27, 3.73
Re: Temp Sending Unit Problem

Thanks, Ill check it out tommorow, and i did have my dash apart to do my speedo cable but the temp gauge still worked after that.
Reply
Old Mar 15, 2008 | 12:37 PM
  #6  
leek157's Avatar
Thread Starter
Member
 
Joined: Jul 2007
Posts: 149
Likes: 0
From: Lisle Illinois
Car: 95 SHO. 87 IROC red 69 Vette blue
Engine: 3.0 Yamahammer.5.7 TPI L98, 350
Transmission: mtx4 ,700r4, 4speed,
Axle/Gears: 3.27, 3.73
Re: Temp Sending Unit Problem

ok I found the sending unit and the wire is not connected at all and the metal tab with the hole in it sticking out isnt there , looking at the wiring diagrams it says its a dark green wire but once again i cant seem to find that wire
Reply
Old Mar 15, 2008 | 06:58 PM
  #7  
IROCmonkey's Avatar
Senior Member
 
Joined: Jun 2002
Posts: 687
Likes: 0
From: Tampa Bay, FL
Car: 85 IROC
Engine: LB9
Transmission: 700R4
Axle/Gears: 3.42
Re: Temp Sending Unit Problem

check along the frame rail, under the steering shaft, and along the firewall...look for a loose wire. It is all alone for like 10-12" before it enters a wire loom
Reply
Old Mar 16, 2008 | 08:37 PM
  #8  
leek157's Avatar
Thread Starter
Member
 
Joined: Jul 2007
Posts: 149
Likes: 0
From: Lisle Illinois
Car: 95 SHO. 87 IROC red 69 Vette blue
Engine: 3.0 Yamahammer.5.7 TPI L98, 350
Transmission: mtx4 ,700r4, 4speed,
Axle/Gears: 3.27, 3.73
Re: Temp Sending Unit Problem

Thanks, ill be sure to look for it
Reply
Old Mar 20, 2008 | 11:35 PM
  #9  
LAFireboyd's Avatar
Supreme Member
20 Year Member
iTrader: (3)
 
Joined: Jan 2004
Posts: 2,960
Likes: 377
From: Las Vegas
Car: 1987 Formula (original owner)
Engine: 305 TPI
Transmission: T5
Axle/Gears: 9-bolt/3.45
Re: Temp Sending Unit Problem

There were two different styles of sending units used during the generation, and the change wasn't a consistent-year change, like the data says, so you could have either style.

If yours doesn't look like the one in the link IROCmonkey posted, then it probably looks like this one:

http://tpiparts.net/inc/sdetail/783

The sender in my '87 is original, and it's like the later style in the link I posted.
Reply
Old Mar 21, 2008 | 01:40 AM
  #10  
leek157's Avatar
Thread Starter
Member
 
Joined: Jul 2007
Posts: 149
Likes: 0
From: Lisle Illinois
Car: 95 SHO. 87 IROC red 69 Vette blue
Engine: 3.0 Yamahammer.5.7 TPI L98, 350
Transmission: mtx4 ,700r4, 4speed,
Axle/Gears: 3.27, 3.73
Re: Temp Sending Unit Problem

That is exactly what mine looks like and i found the clip, it was strange at first because i was expecting a spade type connector, havent had a chance to see if it works yet, the car is still on a lift at school just finished with other misc. wiring diff oil change ,wheel bearings, brakes and many other things
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Glowsock
Tech / General Engine
13
Jul 24, 2025 03:15 PM
Ghettobird52
Tech / General Engine
16
Jul 5, 2024 11:18 PM
Infested
Tech / General Engine
3
May 22, 2018 11:56 PM
Irocohio
Electronics
3
Aug 12, 2015 08:03 AM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 10:56 PM.