sending units
Thread Starter
Member
iTrader: (2)
Joined: Mar 2010
Posts: 166
Likes: 0
From: IOWA
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
sending units
This might be a stupid question but I've never bought gauges before... do they generally come with the requiered sending units or do I have to buy those seperately.
Thread Starter
Member
iTrader: (2)
Joined: Mar 2010
Posts: 166
Likes: 0
From: IOWA
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
Re: sending units
yeah i was looking at the Eguus ones to be spacific.
Supreme Member
Joined: Jan 2006
Posts: 3,341
Likes: 10
From: Mooresville NC
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
Spelling Telling
Some Equus gages come with the sender.
It depends which ones you choose.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
How bout those too scared to drive without headlights in the daytime
and the ones that need headlights for a little rain
.
It depends which ones you choose.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
How bout those too scared to drive without headlights in the daytime
and the ones that need headlights for a little rain.
Thread Starter
Member
iTrader: (2)
Joined: Mar 2010
Posts: 166
Likes: 0
From: IOWA
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
Re: sending units
ok thanks... one more question how much diff. is there between a 2" gauge and a 2 1/16" gauge? The pannel i found to use has holes cut for 2 1/16" gauges and the ones I wanted to use are 2?
Supreme Member
Joined: Jan 2006
Posts: 3,341
Likes: 10
From: Mooresville NC
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
Gage Page
The diameter doesn’t mean anything, it’s the quality that matters.
The 2” gages of course will fit into the 2 1/16” holes.
To center them you can build up the diameter with narrow tape, such as pin striping tape.
Then the locking ring can be applied.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
How Come Some Drivers On The Street Don’t Know How To Make A Turn In One Direction Without Starting By Turning In The Opposite Direction?
.
The 2” gages of course will fit into the 2 1/16” holes.
To center them you can build up the diameter with narrow tape, such as pin striping tape.
Then the locking ring can be applied.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
How Come Some Drivers On The Street Don’t Know How To Make A Turn In One Direction Without Starting By Turning In The Opposite Direction?.
Thread Starter
Member
iTrader: (2)
Joined: Mar 2010
Posts: 166
Likes: 0
From: IOWA
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
Re: sending units
all right thanks... thats what i was thinking but i figured a secound opinion never hurts.
I have yet aother question dose anybody have a wiring diagram for the factory gauges for an 89 iroc (i looked at the diagrams on the autozone site but didn't see one). I was going to try to use the factory wireing and sending units were possible. I assume this would work right?
I have yet aother question dose anybody have a wiring diagram for the factory gauges for an 89 iroc (i looked at the diagrams on the autozone site but didn't see one). I was going to try to use the factory wireing and sending units were possible. I assume this would work right?
Trending Topics
Supreme Member
Joined: Jan 2006
Posts: 3,341
Likes: 10
From: Mooresville NC
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
An EnGAGEing Discussion
Originally Posted by fonzie85
I was going to try to use the factory wireing and sending units were possible. I assume this would work right?
But you should be able to tell by the gage response if you have to replace the sender.
Also, you probably won’t need a diagram.
For example, where they supply you with a new temp sender, you simply replace the old sender, and use the same wire that went to it.
On the gage side, you’ll simply need +, ▬, and the sender wire that went to the old gage.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
How Come Some Drivers On The Street Don’t Know How To Make A Turn In One Direction Without Starting By Turning In The Opposite Direction?.
Thread Starter
Member
iTrader: (2)
Joined: Mar 2010
Posts: 166
Likes: 0
From: IOWA
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
Re: sending units
ic that makes sence thanks again you've been a big help
Thread
Thread Starter
Forum
Replies
Last Post
82xCAMAROxZ28
Engine/Drivetrain/Suspension Parts for Sale
2
Sep 27, 2015 12:31 AM
[CA] 700R4 trans & parts
6998poncho
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 25, 2015 02:56 PM
