[Sold] Holley 950 commander ecu
Thread Starter
Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Holley 950 commander ecu
just as the title says. 950c (it is the upgraded race version) have disks and install /tuning book.
No wiring harness. have pig tails to repin your factory harness if you like.
$500 shipped
http://www.holley.com/534-120.asp
http://www.summitracing.com/parts/HLY-534-181/
No wiring harness. have pig tails to repin your factory harness if you like.
$500 shipped
http://www.holley.com/534-120.asp
http://www.summitracing.com/parts/HLY-534-181/
Last edited by FSTFBDY; Aug 14, 2011 at 09:40 AM. Reason: sold...
Thread Starter
Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Re: Holley 950 commander ecu
Bump before it goes back on the shelf again.
/trade for ?? Weld Pro Stars
/trade for ?? Weld Pro Stars
Last edited by FSTFBDY; Jun 29, 2011 at 05:38 PM.
Senior Member
iTrader: (5)
Joined: Feb 2005
Posts: 691
Likes: 0
From: meridian, idaho
Car: 92 1500p\u 2wd
Engine: 91 z28 tpi 355
Transmission: 91 700r4
Re: Holley 950 commander ecu
how hard is it to repin a 730ecm harness setup to work with this ecm? why didnt u use it?
Thread Starter
Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Re: Holley 950 commander ecu
Acquired it in a trade of other parts.Im running on $59 code for boost and have no reason to really swap ecm's.
Ive repined quite a few harnesses so "FOR ME" its not hard at all.
Its as simple as labeling wires 1st then pulling them out to repin.
Ive repined quite a few harnesses so "FOR ME" its not hard at all.
Its as simple as labeling wires 1st then pulling them out to repin.
Trending Topics
Joined: Aug 2008
Posts: 85
Likes: 25
From: Appleton, WI
Car: 73RS, 85 Iroc, 11 GT
Engine: 383FI, 406 FI, 5.0
Transmission: TKX, TKO600
Axle/Gears: 10 Bolt 3.73s, Strange 12 bolt 3.73
Re: Holley 950 commander ecu
Just so I am clear, exactly what firmware version and software version is this 2.x or 3.x.
Thanks
Thanks
Joined: Aug 2008
Posts: 85
Likes: 25
From: Appleton, WI
Car: 73RS, 85 Iroc, 11 GT
Engine: 383FI, 406 FI, 5.0
Transmission: TKX, TKO600
Axle/Gears: 10 Bolt 3.73s, Strange 12 bolt 3.73
Re: Holley 950 commander ecu
Thanks FSTFBDY,
I have been invesigating this further, the reason for my interest is I have an older 950 MPI setup on my 2nd gen and am looking to upgrade to wideband O2 set-up. I found out I can send the ECU back to Holley for the upgrade and get the wideband O2 and controller for about $310. Dont think I could ask you to drop price to be competitive with this.
I have been invesigating this further, the reason for my interest is I have an older 950 MPI setup on my 2nd gen and am looking to upgrade to wideband O2 set-up. I found out I can send the ECU back to Holley for the upgrade and get the wideband O2 and controller for about $310. Dont think I could ask you to drop price to be competitive with this.
Thread
Thread Starter
Forum
Replies
Last Post
RedLeader289
Tech / General Engine
10
May 28, 2019 01:47 PM
KO1
Engine/Drivetrain/Suspension Parts for Sale
16
Oct 15, 2015 05:00 PM
Royal_Z
Engine/Drivetrain/Suspension Parts for Sale
4
Sep 30, 2015 08:45 PM
