superram, tpi vortec base, modified fuel rails, & 52mm holley tb
12-17-2012, 10:34 AM
#1
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
superram, tpi vortec base, modified fuel rails, & 52mm holley tb
I've got a supperram (plennum and runners), tpi vortec base, fuel rails (been modified see pics) and holley 52mm tb for sale. All parts have right at 1,000 miles on them. Decided to go with a single plane and a ls2 style throttle body for more engine bay room (parts were installed on my '02 blazer)
all the photos shown are when I was putting the engine together, parts will be cleaned prior to shipping(very minimual due to only 1,00 miles in the year and a half the motor was in)
the superram has had the top of the lid milled flat and been painted semi-gloss black (just high temp engine paint)I have all the bolts and screws that hold it all together, needs gaskets: superram by itself, $650+shipping SOLD
the intake has had a couple of the intake bolt holes countersunk to allow the superram runners to clear (see the silver screws in the pic below of the intake): intake by itself, $300+ Shipping
I modified the fuel rails (two driver side fuel rails) so I could feed the runners under the supper ram. the front crossover has been enlarged and tapped for 3/8 npt. the rear cross over is the same way but is connected with some hard line and compression fittings (included) Braided fuel lines and fitting are not included.fuel rails $50+ shipping
The throttle body is a 52mm holley, tps and IAC included (coolant nipples on IAC housing have been cut off) I ditched the holley plate (I hate company logos) and cut my own plate: throttle body $175+ Shipping
all the photos shown are when I was putting the engine together, parts will be cleaned prior to shipping(very minimual due to only 1,00 miles in the year and a half the motor was in)
the superram has had the top of the lid milled flat and been painted semi-gloss black (just high temp engine paint)I have all the bolts and screws that hold it all together, needs gaskets: superram by itself, $650+shipping SOLD
the intake has had a couple of the intake bolt holes countersunk to allow the superram runners to clear (see the silver screws in the pic below of the intake): intake by itself, $300+ Shipping
I modified the fuel rails (two driver side fuel rails) so I could feed the runners under the supper ram. the front crossover has been enlarged and tapped for 3/8 npt. the rear cross over is the same way but is connected with some hard line and compression fittings (included) Braided fuel lines and fitting are not included.fuel rails $50+ shipping
The throttle body is a 52mm holley, tps and IAC included (coolant nipples on IAC housing have been cut off) I ditched the holley plate (I hate company logos) and cut my own plate: throttle body $175+ Shipping
Last edited by ericoo1; 12-26-2012 at 03:37 PM. Reason: Sold superram
12-17-2012, 10:38 AM
#3
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
crap....I clinked the link I have in my favorites to get here and forgot to go to classifieds, pmed a mod and asked for it to be moved, thanks for the heads up
Last edited by ericoo1; 12-17-2012 at 10:41 AM.
12-18-2012, 09:50 AM
#4
Supreme Member
iTrader: (15)
Join Date: Oct 2003
Location: Charlestown, IN
Posts: 3,449
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1971 Camaro
Engine: 427
Transmission: TKO600
Axle/Gears: 3.73
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
That looks killer in the black. Love the setup, good luck with the sale!
12-18-2012, 10:03 AM
#5
Member
iTrader: (1)
Join Date: Feb 2009
Location: Hortonville, Wisconsin
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
Car: 82 Firebird
Engine: Boosted LSX
Transmission: Built 4L60E
Axle/Gears: 4th Gen 3.42s
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
beautiful looking setup! glws
12-18-2012, 10:10 AM
#6
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
yeah it looked great, I just didn't have any room up front for an air intake without it getting heat soaked by the radiator.
switched to a single plane so I can point the throttle body to the pass. side.
switched to a single plane so I can point the throttle body to the pass. side.
Trending Topics
12-27-2012, 12:29 PM
#8
Member
Join Date: Dec 2010
Location: Milledgeville, GA
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro Z28
Engine: L98
Transmission: 86' 700R4
Axle/Gears: 10 Bolt, 3.42's
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
How much for just the intake?
12-28-2012, 01:12 PM
#9
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
$350 shipped for just the intake. I will not be able to ship it till Wed. though. It is at my job and we are closed untill the 2nd.
01-06-2013, 10:53 PM
#11
Want a title? Post!
Join Date: Sep 2011
Location: Los Angeles
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Car: 79 El Camino / 89 Camaro RS
Engine: 350ci El Co/ 305ci RS
Transmission: 700R4 ON BOTH
Axle/Gears: STOCK 7.5, Posi El Co/ Open RS
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
pMD
01-15-2013, 07:36 PM
#12
Member
iTrader: (1)
Join Date: May 2012
Location: PHX, AZ
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 K5 Blazer
Engine: 1992 5.7L TPI
Transmission: 700R4
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
Throttle body require new TPS if going from 48mm?
01-16-2013, 08:03 AM
#13
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
nope
I'll lower the price to $320 shipped on the SPDC vortec intake
I'll lower the price to $320 shipped on the SPDC vortec intake
Last edited by ericoo1; 01-16-2013 at 08:09 AM.
03-18-2013, 09:17 AM
#15
Junior Member
Thread Starter
Join Date: Oct 2002
Location: Fort Worth, TX
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Car: 89 silverado,02 s10 blazer
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
intake is gone, the only thing I have left is the throttle body, $160 shipped
03-25-2013, 09:23 AM
#16
Member
iTrader: (3)
Join Date: Jul 2009
Posts: 490
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Camaro RS
Engine: 350 Vortec Demon 650CFM
Transmission: 700R4
Axle/Gears: Posi
Re: superram, tpi vortec base, modified fuel rails, & 52mm holley tb
same size as stock throttle body?
Thread
Thread Starter
Forum
Replies
Last Post
1992rs/ss
NW Indiana and South Chicago Suburb
12
05-19-2020 07:02 PM
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
08-12-2015 03:41 PM
