I think the topic pretty much sums it up. I will be swapping the 350 from my 89 RS into My 91 RS. I will be installing Hooker 2055's, 180 deg stat,and fan switch at the same time. I am buying an engine hoist in the next couple of days.
Do I need to take off all the accessories, or can I leave them on and take out the radiator?

Basically, I need to know S.O.P. for an motor swap.

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!

 

Yes, you can install the motor with the accessories attached. Since you are buying an engine hoist, I might suggest you get another tool that would connect to the hoist. Summit sells them, they call it an engine tilter/engine loader. This would allow you to make the fine adjustment need to slide your motor into your engine compartment.

 

I fully agree with 86z/92rs's recommendation on the tilt sling. It's great to have for any engine pull/install, whether "switch" or "swap".

------------------
82 Berlinetta, orig V-6 car, now w/86 LG4/TH700R4. 2.93 limited slip. Cat-back from '91 GTA, ZZ3 intake, Accel HEI SuperCoil. AMSOIL syn lubes bumper-to-bumper. Daily driver, work-in-progress (LG4 w/'87 LB9 block, ZZ3 cam, ported World 305 heads, Hooker headers & y-pipe, 3" Catco cat & 3" cat-back, Spohn SFCs).
57 Bel Air, my 1st car. '66 396, 9.7 CR forged TRWs, Weiand Action+, Edelbrock 1901 Q-Jet (Holley 3310 on the way), GK 270 cam, Magnum rockers, Jacobs Omnipack, 1-3/4" Hedders & 3" Warlocks, TH400 w/TCI Sat Night Special conv & Trans-Scat shift kit, MegaShifter, 3.08 8.2" 10-bolt w/Powertrax, AMSOIL syn lubes bumper-to-bumper. Idles smooth @ 600 RPM in D. Best 15.02/95.06 @ 5800' Bandimere (corrected 13.93/102.4 @ sea level).

[This message has been edited by five7kid (edited August 26, 2001).]

 

The hoist I'm buying comes with the tilter. I'm getting one from Advanced Auto Parts for $220.
Any other tips?

Also, I know there is a site where you can enter the engine casting numbers and find out the year, etc. of the engine. Anybody have this link handy?

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!

 

Someone has to know!!

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!

 

I guess not.

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!

 

www.mortec.com

That should pretty much give you all the info that you're looking for.

AJ

------------------
92 RS w/t-tops 305 TBI Auto.
170K miles and don't burn a drop o'oil
-K&N Truck filter #1500 w, open ele.
air cleaner
-Dynomax 2 1/2" cat-back
-B&M TransPak
-Jet Stage2 Chip
-180* T-Stat w/ 185* Fan Switch
-JVC CD--Alpine speakers & 4ch. amp
Rockford Punch 100. 1 - MTX 12" sub

 

Now would be a good time to replace the motor mounts if you havent already.

 

Thanks for the info guys.

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!

 

Check out my new thread "This sucks a big one!" For the results of my motor pull.

------------------
89 RS 350 TBI auto Hooker SC/LT headers Open element 3in K&N CVT protorque mini-starter

Daily driver 91 RS auto LO3 63k

New project- 89 Formula 350 WS6
383 or 400 to come!