Eveyone w/ Serpentine systems
Thread Starter
Senior Member
iTrader: (3)
Joined: Jul 1999
Posts: 844
Likes: 0
From: Long Island, NY
Car: 1987 GTA
Engine: 645hp/656 ft lb Blown 383
Transmission: 700-R4 3,000 stall
Axle/Gears: 3.55 moser 12-bolt
Eveyone w/ Serpentine systems
I was hoping somebody could give me either the size specifications or the part #'s of the 4 bolts that bolt the passanger side sepntine bracket to the motor. This is the bracket that holds the a/c compressor, smog pump and tensioner. thanks a lot
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
Here's what I could tell from looking in my parts catalog:
2 bolts down at the bottom, p/n 14091547 (TORX 3/8-16X1 1/8)
1 stud p/n 10055883 (SECD AIR INJN PUMP & DRV BELT TENSR BRKT 9.52X69.85) with a nut p/n 14057004 (HEX FLANGE 3/8-16 PC 286M)
2 studs for the A/C compressor that in turn connects to 2 braces that connect to the block. Stud p/n 10055888 (A/C CMPR M10X1.5X110, 3/8-16X20) and both use nut p/n 14057004
The braces are p/n 10105267 (LWR) and 10105292 (UPR)
The end of the braces that go into the block use stud p/n 14057279 and nuts p/n 14057004 except L98/LB9 get bolt p/n 11508106 (HFH M8X1.25X25 9.8 POR) instead of one of the studs.
Other than that there is one bolt p/n 14089928 (M12X1.75X36) that bolts the A/C compressor to the bracket.
I included all the parts that the parts catalog showed, not just the bolts that you asked for. The stuff inside the parenthesis () are the part descriptions that the catalog gave for each part. Hope that helps.
2 bolts down at the bottom, p/n 14091547 (TORX 3/8-16X1 1/8)
1 stud p/n 10055883 (SECD AIR INJN PUMP & DRV BELT TENSR BRKT 9.52X69.85) with a nut p/n 14057004 (HEX FLANGE 3/8-16 PC 286M)
2 studs for the A/C compressor that in turn connects to 2 braces that connect to the block. Stud p/n 10055888 (A/C CMPR M10X1.5X110, 3/8-16X20) and both use nut p/n 14057004
The braces are p/n 10105267 (LWR) and 10105292 (UPR)
The end of the braces that go into the block use stud p/n 14057279 and nuts p/n 14057004 except L98/LB9 get bolt p/n 11508106 (HFH M8X1.25X25 9.8 POR) instead of one of the studs.
Other than that there is one bolt p/n 14089928 (M12X1.75X36) that bolts the A/C compressor to the bracket.
I included all the parts that the parts catalog showed, not just the bolts that you asked for. The stuff inside the parenthesis () are the part descriptions that the catalog gave for each part. Hope that helps.
Thread Starter
Senior Member
iTrader: (3)
Joined: Jul 1999
Posts: 844
Likes: 0
From: Long Island, NY
Car: 1987 GTA
Engine: 645hp/656 ft lb Blown 383
Transmission: 700-R4 3,000 stall
Axle/Gears: 3.55 moser 12-bolt
yes, it helps a lot! thanks very much, I appreciate it. I got some other part #'s, but I guess they are wrong. 10105201 and 10105202. you don't happent o know what they are for do you? thanks -justin
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 15, 2001).]
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 15, 2001).]
Oops, my bad! When I looked up that info, I just looked in the section for the A/C system and did not look at the smog pump setion. Both of those part numbers (10105201,10105202) are bolts that hold the smog pump to the bracket.
10105201 (BOLT, SECD AIR INJN PUMP (UPR) 3/8-16X5.90)
10105202 (BOLT, SECD AIR INJN PUMP (LWR) 3/8-16X3.75)
10105201 (BOLT, SECD AIR INJN PUMP (UPR) 3/8-16X5.90)
10105202 (BOLT, SECD AIR INJN PUMP (LWR) 3/8-16X3.75)
Thread Starter
Senior Member
iTrader: (3)
Joined: Jul 1999
Posts: 844
Likes: 0
From: Long Island, NY
Car: 1987 GTA
Engine: 645hp/656 ft lb Blown 383
Transmission: 700-R4 3,000 stall
Axle/Gears: 3.55 moser 12-bolt
so they go through to the block? I have one that just goes into the bracket and the other one, i'm missing, it seems as if it goes throught to the block. which is which.? is there any way i can view these diagrams on-line.? thanks a lot, you've been very helpful.
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 16, 2001).]
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 16, 2001).]
Trending Topics
Good pics, Dana. There are 4 bolts that hold the bracket. 2 upper ones in the head, and 2 lower ones in the block.
Upper:
Page 3-92, #8 10105202 Also holds Smog pump
Page 3-92, #6 and #7 - 10055883, 14057004
Lower:
Page 9-26, #7 14091547. 2 of these.
------------------
1989 IROC-Z 5.7L
[This message has been edited by Omar (edited February 19, 2001).]
Upper:
Page 3-92, #8 10105202 Also holds Smog pump
Page 3-92, #6 and #7 - 10055883, 14057004
Lower:
Page 9-26, #7 14091547. 2 of these.
------------------
1989 IROC-Z 5.7L
[This message has been edited by Omar (edited February 19, 2001).]
Thread Starter
Senior Member
iTrader: (3)
Joined: Jul 1999
Posts: 844
Likes: 0
From: Long Island, NY
Car: 1987 GTA
Engine: 645hp/656 ft lb Blown 383
Transmission: 700-R4 3,000 stall
Axle/Gears: 3.55 moser 12-bolt
that's excactly what I needed! thank you both very much.
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 18, 2001).]
------------------
SUPERCHARGED 87 GTA: Blk/Gld w/Superam, 355cid Trickflows, forged pistons 9.5:1. Auto 2,600 stall, 3.45 9 bolt disc, Best time & mph (Naturally Aspirated): 13.567 @ 101.900 w/ a poor 60ft. Best mph: 104.3 *This car is 100% NYS emissions legal, w/ all emissions controls!* "If you want to have a fast car, hang out w/ those who do!"
http:// www.community.webtv.net/munks87/JustinsGTApage.com
VORTECH S-TRIM, INSTALLATION IN PROGRESS: 10 & 15 LB> PULLEYS, CUSTOM HKS RACE BYPASS, CUSTOM DUCTING W/ COLD AIR, SWAPPING TO SERPENTINE, & MANY EXTRAS! BEST TIME: 11'S I GUESS. WE'LL SEE IN SPRING!
[This message has been edited by Justin 87 GTA (edited February 18, 2001).]
Member
iTrader: (1)
Joined: Jun 2000
Posts: 266
Likes: 0
From: Bow, WA
Car: 1989 Firebird Formula 350
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: Borg Warner 3.27
Dana92RS-Where did you get that parts catalog?
------------------
'89 Firebird Formula-
K&N Air Filter, Holley Throttle Body Air Foil, Hotchkis Strut Tower Brace, Hotchkis Panhard Rod, Hotchkis Trailing Arms, Kenny Brown Subframe Connectors, GT Auto Assesories aero wing
------------------
'89 Firebird Formula-
K&N Air Filter, Holley Throttle Body Air Foil, Hotchkis Strut Tower Brace, Hotchkis Panhard Rod, Hotchkis Trailing Arms, Kenny Brown Subframe Connectors, GT Auto Assesories aero wing
Thread
Thread Starter
Forum
Replies
Last Post






