No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Thread Starter
Joined: Jul 2010
Posts: 833
Likes: 17
From: The Jersey Shore
Car: 1991 Firebird Convertible
Engine: 5.7 L98
Transmission: 700R4
Axle/Gears: 3.45 9 Bolt Posi
No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
So not sure where to post this since we dont have a 'lounge' type board but if you were building a tool box to only work on 3rd gens what would you put in it?
If this is a stupid thread so be it
If this is a stupid thread so be it
Supreme Member
iTrader: (1)
Joined: Mar 2010
Posts: 1,088
Likes: 0
From: Goose Creek, SC
Car: 1987 IROC-Z and 1988 Iroc-Z
Engine: 5.7 350 V8 and 5.0 305 V8
Transmission: 700R4 Automatic Transmission
Axle/Gears: 3.27 Posi
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Just a hammer.....maybe a screwdriver or two.
Joined: Aug 2005
Posts: 285
Likes: 1
From: baldwin city, ks
Car: 84 454 monte, 89 formula, 86 camaro
Engine: the bigger the better
Transmission: 700/4L60 in everything
Axle/Gears: wish they were all 4.10's or better
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Nitrous AND a super charger !!!!
Member
Joined: Sep 2012
Posts: 100
Likes: 0
From: N.W. burbs chicago
Car: '92 RS heritage convertible
Engine: 305
Transmission: auto
Axle/Gears: 2.73
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
A 6 Pack of your favorite brew, And some Cash !
Supreme Member
iTrader: (3)
Joined: Jun 2009
Posts: 2,350
Likes: 3
From: Mid West
Car: '87 Camaro
Engine: '92 Carb'd 350
Transmission: 700r4
Axle/Gears: factory stock
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Complete set of ratchet wrenches in metric & sae
Same in sockets, 1/4, 3/8 & 1/2 inch drives
Pickle fork
Air compressor full socket sets
Screw driver sets
Torx sets
Line wrench sets
Same in sockets, 1/4, 3/8 & 1/2 inch drives
Pickle fork
Air compressor full socket sets
Screw driver sets
Torx sets
Line wrench sets
Member
Joined: Sep 2007
Posts: 340
Likes: 0
From: bremerton
Car: 87 trans am
Engine: 5.7
Transmission: t-5
Axle/Gears: 9 bolt posi 3:27
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
uhm pneumatic that is all. Sucks having to do everything by hand with wrench and ratchet. Only have a 2 gallon air compressor that powers my air ratchet for maybe 4 turns before it peters out. anyone in the bremerton wa area wanna give me a good compressor since the wife says i can't afford one?
Trending Topics
Junior Member
iTrader: (1)
Joined: Jun 2008
Posts: 44
Likes: 0
From: Leavenworth, Kansas
Car: 1991 Camaro z28
Engine: 350 t.p.i.
Transmission: 700r4
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
A complete set of assorted bolt/nut/retainer kit like the ones at Carquest. The retainers on these cars are ridiculous!
Senior Member
iTrader: (6)
Joined: Sep 2007
Posts: 697
Likes: 0
From: Adelanto, Ca/ El Paso, Tx
Car: 84 Camaro Z28
Engine: 355 Carb
Transmission: T5
Axle/Gears: 3.42
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Just have a universal tool set and some cash
Member
Joined: Nov 2004
Posts: 332
Likes: 0
From: Houston MS
Car: 87 GTA Trans Am
Engine: 305 TPI
Transmission: 700R4
Axle/Gears: 10 bolt posi 3.23
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
My number one tool is this forum followed by my factory service manual.
Actually I think the manual may be in first. LOL
Actually I think the manual may be in first. LOL
Supreme Member
Joined: Jun 2005
Posts: 1,380
Likes: 6
From: Sydney, Australia
Car: '86 TA
Engine: '74 350
Transmission: 700r4
Axle/Gears: 2.77
Re: No Doubt A Pointless Thread, But Lets Build The Perfect 3rd Gen Tool Box
Same as any other car I've owned. Flat and philips drivers, 10-14mm spanners, pliers & sidecutters, multimeter, duct tape, spool of wire, and MOST important - locking pliers. Gets me out of most scrapes.
Assume we are just talking the roadside toolbox here.
Assume we are just talking the roadside toolbox here.
Thread
Thread Starter
Forum
Replies
Last Post
1992rs/ss
NW Indiana and South Chicago Suburb
14
Jan 31, 2025 05:10 PM
eightsixseven
Tech / General Engine
2
Dec 16, 2024 01:50 PM
Terrell351
Engine/Drivetrain/Suspension Parts for Sale
5
Jun 13, 2021 01:13 PM
1992rs/ss
Engine/Drivetrain/Suspension Parts for Sale
16
Jan 28, 2016 09:58 PM