Third Generation F-Body Message Boards
The notch at the left was necessary to clear my big electric water pump, the opening you see behind it is the end of the guide slot for the nut that the adjustment bolt threads into
The notch at the left was necessary to clear my big electric water pump, the opening you see behind it is the end of the guide slot for the nut that the adjustment bolt threads into
0 2017/05/23 16:52:39
I cut off and epoxied shut the original return, found a thick spot that I drilled and tapped for a new fitting and epoxied that in when I confirmed the angle.
I cut off and epoxied shut the original return, found a thick spot that I drilled and tapped for a new fitting and epoxied that in when I confirmed the angle.
0 2017/05/23 16:52:55
0 2017/05/23 16:53:02
0 2017/05/23 16:53:10
Y pipe welded in. you can see where I added the 1" section
Y pipe welded in. you can see where I added the 1" section
0 2017/05/28 03:25:50
I hate when people leave these things without turndonws, and I hate soot covering the bottom of my car.
I hate when people leave these things without turndonws, and I hate soot covering the bottom of my car.
0 2017/05/28 03:25:53
I don't know what happened to the original wiring but the boot was messed up, I just put a wad of paper in there to keep stuff away from the motor and filled it with RTV. The original harness was gone so I cut off the QTP connection and put a 2pin trailer harness style connector on it.
I don't know what happened to the original wiring but the boot was messed up, I just put a wad of paper in there to keep stuff away from the motor and filled it with RTV. The original harness was gone so I cut off the QTP connection and put a 2pin trailer harness style connector on it.
0 2017/05/28 03:25:57
Everything all neat and tidy. I threw the turndown in the blast cabinet and then coated it with black ceramic :-P
Everything all neat and tidy. I threw the turndown in the blast cabinet and then coated it with black ceramic :-P
0 2017/05/28 03:26:01
Everything installed and you can see where the wiring ended up.
Everything installed and you can see where the wiring ended up.
0 2017/05/28 03:26:04
5 minute sketchup ;) The center hole is pretty non-critical size wise, as long as the shift lever doesn't hit it.
5 minute sketchup ;) The center hole is pretty non-critical size wise, as long as the shift lever doesn't hit it.
0 2017/06/24 15:37:08
It's hard to tell but the shift lever bends right where the pin goes through it
It's hard to tell but the shift lever bends right where the pin goes through it
0 2017/06/26 04:39:39
turned slightly, you can see it's not a straight fore and aft or side to side bend, it's in 2 axis, and if you redrill a new hole for the pin above the original hole the lever/ball will no longer sit under the pivot
turned slightly, you can see it's not a straight fore and aft or side to side bend, it's in 2 axis, and if you redrill a new hole for the pin above the original hole the lever/ball will no longer sit under the pivot
0 2017/06/26 04:39:42
0 2017/06/28 15:11:18
0 2017/06/29 22:18:35
0 2017/06/29 22:22:17
This is about as close as you can get it to line up
This is about as close as you can get it to line up
0 2017/06/29 22:27:21
Yes, my pin sheared off trying to press it out of the new hole in just above the bend in the stick >:-(
Yes, my pin sheared off trying to press it out of the new hole in just above the bend in the stick >:-(
0 2017/06/29 22:29:59
0 2017/07/20 20:11:51
Huh, no blockoff plate but a few versions of the bezel exist already...
Huh, no blockoff plate but a few versions of the bezel exist already...
0 2017/09/18 02:25:00
0 2017/09/21 04:16:51
by the time you out this on the door it would look too long
by the time you out this on the door it would look too long
0 2017/09/21 04:34:28
I don't know, I think that this looks kind of stupid...
I don't know, I think that this looks kind of stupid...
0 2017/09/21 04:36:59
0 2017/10/23 02:07:59
0 2017/11/01 03:39:59
0 2017/11/01 03:40:00
0 2017/11/01 03:40:01
0 2017/11/01 03:40:02
0 2017/11/01 03:40:04
0 2017/11/17 12:25:20
0 2018/01/23 11:54:22
0 2018/01/29 04:09:14
0 2018/01/29 04:29:03
0 2018/01/29 04:32:34
0 2018/03/16 14:53:23
0 2018/03/16 14:53:28
I'm surprised they have it, it's listed as plastic...
I'm surprised they have it, it's listed as plastic...
0 2018/03/16 17:57:31
Hey, it works...
Hey, it works...
0 2018/03/26 11:23:59
0 2018/04/08 05:30:06
0 2018/04/08 05:30:16
0 2018/04/08 17:24:32