Third Generation F-Body Message Boards
One of the ports with less of it, but you can see it looking like a crack in the carbon deposits
One of the ports with less of it, but you can see it looking like a crack in the carbon deposits
0 2021/09/19 16:52:42
The other one that isn't as bad, in this case clearly wet but not as long as the rest.
The other one that isn't as bad, in this case clearly wet but not as long as the rest.
0 2021/09/19 16:53:10
I found 3 mud dauber nests inside the cylinders...
I found 3 mud dauber nests inside the cylinders...
0 2021/09/21 14:09:57
Passenger's side with the inner fender pulled away
Passenger's side with the inner fender pulled away
0 2021/12/03 13:17:26
Passenger's side
Passenger's side
0 2021/12/03 13:17:35
Driver's side
Driver's side
0 2021/12/03 13:18:00
0 2021/12/03 13:18:31
0 2021/12/03 13:18:44
0 2021/12/03 18:15:51
0 2021/12/16 02:45:44
0 2023/04/28 01:34:56
0 2023/04/28 01:39:11
0 2023/07/06 19:53:48
0 2025/02/22 03:19:16
In the future, I cut a 2x4 the length of the space between the fenders, strapped a couple of rachet straps to the front of the cylinder heads and I was able to lift the engine off the eventually to install a new K and suspension. It was surprisingly not in the way and a single strap could have held it but I liked the security of 2 straps in case one let go
In the future, I cut a 2x4 the length of the space between the fenders, strapped a couple of rachet straps to the front of the cylinder heads and I was able to lift the engine off the eventually to install a new K and suspension. It was surprisingly not in the way and a single strap could have held it but I liked the security of 2 straps in case one let go
0 2025/05/08 03:07:38
For those of you that don't know, the early 3rd gens had a crazy factory exhaust with small dual mufflers, this is the only picture that I could find. The 2 pieces in the middle are the Y pipe and the intermediate pipe, that connected to the Y at the bottom that split into 2 smaller pipes going up over the axle, and on the other side the 2 smaller pipes went into the center pipe which went into the mufflers on either side and out the tailpipes.
For those of you that don't know, the early 3rd gens had a crazy factory exhaust with small dual mufflers, this is the only picture that I could find. The 2 pieces in the middle are the Y pipe and the intermediate pipe, that connected to the Y at the bottom that split into 2 smaller pipes going up over the axle, and on the other side the 2 smaller pipes went into the center pipe which went into the mufflers on either side and out the tailpipes.
0 2025/05/19 00:29:54
Something like this, this sounded great but wouldn't pass emissions, I could never get the flow the same from one side to the other and if one pipe measured lower then the other they assumed that you were trying to pump air into the exhaust to lower the emissions and you automatically failed. Of course, this was in 1991, when the car still needed to pass emissions.
Something like this, this sounded great but wouldn't pass emissions, I could never get the flow the same from one side to the other and if one pipe measured lower then the other they assumed that you were trying to pump air into the exhaust to lower the emissions and you automatically failed. Of course, this was in 1991, when the car still needed to pass emissions.
0 2025/05/19 00:42:28
This is posted the same way as the others, will it work?
This is posted the same way as the others, will it work?
0 2025/05/20 02:47:03
0 2025/05/20 03:44:32
0 2025/06/12 16:42:12
0 2025/11/16 02:41:17
0 2025/11/16 03:18:10