Front Bumper Cover Nut Size
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2013
Location: Lexington, KY
Posts: 20
Received 0 Likes
on
0 Posts
Car: 1988 GTA
Front Bumper Cover Nut Size
Ok, once again I searched and couldn't find anything. I'm looking for the thread size of the nut that attaches the front bumper through the fender. I'm not near the car so unfortunately I can't look at it, but I seem to recall there just being a stud towards the top of the bumper cover. I hope I'm remembering correctly. It's for a Firebird.
#4
Supreme Member
iTrader: (1)
Join Date: Aug 2008
Location: Short Summer, VT
Posts: 1,485
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1985 Trans Am T-Top
Engine: 305 TPI
Transmission: T-5 5 Speed
Axle/Gears: 3.42 posi 1LE 10 bolt
Re: Front Bumper Cover Nut Size
It is a threaded stud, I don't know if I've ever seen what the factory originally had there, no car I've worked on had the original hardware there. The original fitting was probably some sort of speed nut or push retainer. I'll go measure the support bar I have and see what size it is.
#5
Supreme Member
iTrader: (1)
Join Date: Aug 2008
Location: Short Summer, VT
Posts: 1,485
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1985 Trans Am T-Top
Engine: 305 TPI
Transmission: T-5 5 Speed
Axle/Gears: 3.42 posi 1LE 10 bolt
Re: Front Bumper Cover Nut Size
Checked it out, not really threaded, but I think it is a push type retainer. This is an 89 formula. It us about m6 size so you. Ight be able to crank a nut on it.
Here's a pic.
I think this is what fits it:
http://www.clipsandfasteners.com/M6_...c_p/a14980.htm
Here's a pic.
I think this is what fits it:
http://www.clipsandfasteners.com/M6_...c_p/a14980.htm
#6
Member
iTrader: (1)
Join Date: Mar 2010
Location: ohio
Posts: 170
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Trans Am
Engine: 355 Carb. Nitrous 100 shot
Transmission: TCI Performance Trans. 350 Turbo
Axle/Gears: Borg & Warner 9 bolt 3.70 gears
Re: Front Bumper Cover Nut Size
Did anyone ever figure out what size the self threading nuts are? I picked up some M6 and they are definitely to small.
#7
Member
Join Date: Mar 2009
Location: Vancover, BC
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 firebird
Engine: 2.8 MFI
Transmission: T-5
Axle/Gears: 3.42
Re: Front Bumper Cover Nut Size
Its an automotive speed nut.
I have no idea what size it is. I just bought a package of assorted sizes from the local car parts store and some of them fitted. they cut their own thread
I have no idea what size it is. I just bought a package of assorted sizes from the local car parts store and some of them fitted. they cut their own thread
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM