88camaroz28

iTrader: (1)

For Sale is a 1970’s Chevrolet 350 that has been bored 30 over and is now a 383. It makes around 500hp and has tons of torque. It currently has about 2,000 miles on it and is just broken in. I have gone through 2 oil changes on it, one at 1,000 miles and the other at 2,000 just before winter of last year. The motor was professionally built and balanced, it was built in July on 2007. I am selling the motor as a complete running motor with a th350 trans. It has also 2,000 miles on it and is a brand new transmission with a 3500 stall and a stage 2 B&M shift kit. About the motor:

-Full SCAT forged rotating assembly (balanced and blueprinted)
-Keith Black HypereutecticFlat top pistons
-10.5 to 1 compression ratio
-All ARP Studs throughout motor
-Melling High Volume Oil Pump
-Moroso 6qt. oil pan
-Comp Cams 292 Magnum Cam and Lifters
-Comp Cams High Energy Pushrods
-Crane Gold Race Rockers 1.6 ratio
-Dart Pro 1 Heads with 215cc intake runner and 64cc combustion chamber
-Edelbrock Victor Jr. Intake
-Comp Cams Magnum Double Roller Timing Chain
-Wieland High Volume Aluminum Water Pump
-Edelbrock 750cc Carb with vacuum secondaries
-HEI Distributor with Moroso tune-up kit and 8.5mm wires with boot covers
-March V-Belt Accessory Drive
- TCI SFI approved flex plate
-Turbo 350 Transmission
-3500 Stall Converter
-B&M stage 2 shift kit

If you have any questions please ask. I am asking $7500 for the complete setup. Over $10,000 invested, my loss is your gain. I am located in the base of the thumb in Michigan.

Thanks
Dan

88camaroz28

iTrader: (1)

Also it is currently in the car so you can hear it run and drive.

Thanks
Dan

88camaroz28

iTrader: (1)

KamikazeIroccy

iTrader: (1)

willing to sell motor minus intake? ie.Longblock

88camaroz28

iTrader: (1)

PM sent

86transam383

really, all in honesty, you wont get that kinda money for that engine.

tylersb350

snake70

your right

KamikazeIroccy

iTrader: (1)

88camaroz28

iTrader: (1)

Well to build a motor like this one it would cost a ton more and this motor is ready to just bolt in and go. It needs nothing. You know if I sell this motor then it will be a bonus for me but if I dont then I wont be dissapointed either.

KamikazeIroccy

iTrader: (1)

FYI, TPIS techs told me on the phone that I can get a custom engine built from them for $4500 and thats RTR done to the bolts. May I had that this is a roller block and with the 1pc rear main seal along with 2-bolt block splayed for 4 bolt!!
You should just keep your motor, I see you have no post,Well on this site we try and give our fellow members unbelievable deals. MEMBERS ONLY PRICING

88camaroz28

iTrader: (1)

Well thanks for the info. And best of luck to you on your build.

FSTFBDY

iTrader: (33)

why bother posting BS like this if your not gona buy it. Go price everything out and built one yourself for less.

for a 383 and tranny thats a decent deal for someone who is willing to spend some $.

GOOD LUCK ON YOUR SELL. You might want to post it over on racingjunk.com Stuff sells there 10x faster then on here. about to go list the stuff in my sig on there also. 383/Th400 combo etc...

coreybear08

are you willing to seperate the heads??

88camaroz28

iTrader: (1)

THANK YOU!



Sorry I would really like to just sell it complete. If I dont sell it in the next month though I might be willing to separate them. Ill get back with you if it doesnt sell

Thanks
Dan