rear, flywheel, disc brake master cylinder, motor
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: woodstock, GA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc Camaro
Engine: 383
Transmission: 700r4
Axle/Gears: 373 gears
rear, flywheel, disc brake master cylinder, motor
-i got a disc brake rear end with the rear sway bar $200
-i have an aluminum flywheel for a t56 to go behind a small block (new) $100
-i also got a brake booster with the master cylinder and prop valve for a disc/disc setup $75
-lastly i have a freshly machined 350 tourque plate honed to a 355. the crank has been polished and the block and crank are completely ready to go. it comes with the original rods and pistons but will need new pistons but the rods are fine. it has the big valve 882 heads that just need to be cleaned up. it comes with a new remanufactured standard intake that has been milled for increased flow. i also have an oil pan for the motor and an old distributor. this motor is orginally out of a 1968 camaro. for everything i am looking for $425
-i have an aluminum flywheel for a t56 to go behind a small block (new) $100
-i also got a brake booster with the master cylinder and prop valve for a disc/disc setup $75
-lastly i have a freshly machined 350 tourque plate honed to a 355. the crank has been polished and the block and crank are completely ready to go. it comes with the original rods and pistons but will need new pistons but the rods are fine. it has the big valve 882 heads that just need to be cleaned up. it comes with a new remanufactured standard intake that has been milled for increased flow. i also have an oil pan for the motor and an old distributor. this motor is orginally out of a 1968 camaro. for everything i am looking for $425
#2
Senior Member
iTrader: (1)
Join Date: Sep 2006
Location: Canada
Posts: 962
Likes: 0
Received 13 Likes
on
10 Posts
Car: 1979 Malibu
Engine: Blown LSx
Transmission: T56 Magnum
Axle/Gears: 9"/wavetrac/35's/3.70
Re: rear, flywheel, disc brake master cylinder, motor
Is this flywheel for a 1 pc or 2 pc RMS??? interested, got any pics???
#3
Junior Member
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: woodstock, GA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc Camaro
Engine: 383
Transmission: 700r4
Axle/Gears: 373 gears
Re: rear, flywheel, disc brake master cylinder, motor
Trending Topics
#9
Junior Member
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: woodstock, GA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc Camaro
Engine: 383
Transmission: 700r4
Axle/Gears: 373 gears
Re: rear, flywheel, disc brake master cylinder, motor
the number is F 091059. i know its for a two peice rear main because i have the engine that it was going to be used with and it is a two peice rear main engine. the center hole is right at 2.5".
#11
Member
iTrader: (5)
Join Date: Apr 2006
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Monte Carlo SS
Engine: 5.7L
Transmission: WC T-5
Axle/Gears: 3.73:1
Re: rear, flywheel, disc brake master cylinder, motor
What's the overall thickness of the flywheel (just to compare with the stock T56 flywheel I have)? Do you have any other pics from a different angle?
How much would shipping through USPS be to Ontario, Canada?
How much would shipping through USPS be to Ontario, Canada?
#12
Junior Member
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: woodstock, GA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc Camaro
Engine: 383
Transmission: 700r4
Axle/Gears: 373 gears
Re: rear, flywheel, disc brake master cylinder, motor
sorry for the delay ive been busy. the overall thickness is right at an inch and including the external balance its dead on an inch. usps to you would be $35. and heres some pics:
#13
Member
iTrader: (5)
Join Date: Apr 2006
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Monte Carlo SS
Engine: 5.7L
Transmission: WC T-5
Axle/Gears: 3.73:1
Re: rear, flywheel, disc brake master cylinder, motor
Thanks for the pics, but I'll have to pass - this looks like a standard external balance flywheel for a 2pc rear main motor.
A T56 flywheel would be around 1.75" thick, and I need one that's for an internal balance motor.
A T56 flywheel would be around 1.75" thick, and I need one that's for an internal balance motor.
Last edited by 85_SS; 01-22-2010 at 03:12 PM.
#14
Junior Member
iTrader: (3)
Join Date: May 2009
Location: Media, PA
Posts: 69
Likes: 0
Received 6 Likes
on
5 Posts
Car: 89 Vert Camaro
Engine: 3.8SFI Turbo
Transmission: 200R4
Axle/Gears: 3.42
Re: rear, flywheel, disc brake master cylinder, motor
What year did the rear come out of? and what is the ratio?
Thread
Thread Starter
Forum
Replies
Last Post
hectre13
Engine/Drivetrain/Suspension Parts for Sale
2
12-11-2023 08:14 AM
sailtexas186548
Engine/Drivetrain/Suspension Parts for Sale
8
01-19-2016 12:21 PM