turn signal lever swap
#1
Junior Member
Thread Starter
Join Date: Feb 2008
Location: st catharines ontario
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2004 Silverado SS
Engine: 6.0L LQ9
Axle/Gears: 4.10 AWD
turn signal lever swap
i just bought my 1988 gta, and the turn signal lever looks like crap and the guy gave me a new one from gm to swap in, so my question is, how?
#2
Supreme Member
iTrader: (1)
Join Date: Aug 1999
Location: Rowlett, TX
Posts: 2,842
Likes: 0
Received 5 Likes
on
5 Posts
Car: 1988 GTA
Engine: 5.0 TPI
Transmission: T5
Axle/Gears: 9 Bolt, 3.45
Re: turn signal lever swap
Grab it by the base (the part of it that doesnt rotate), push in, and turn CCW about 1/4 turn. It should then pull out, it might take a little wiggling though. The wire for it runs down the column, and plugs in under the dash. Unplug it, pull the old wire out, and fish the new wire down the column, then install the new one.
#3
Junior Member
Thread Starter
Join Date: Feb 2008
Location: st catharines ontario
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2004 Silverado SS
Engine: 6.0L LQ9
Axle/Gears: 4.10 AWD
Re: turn signal lever swap
thats it? seriously!?! i was thinking i would need to take the steering column apart similar to when i had to tighten it.
#5
Member
iTrader: (1)
Join Date: Apr 2008
Location: hudson valley, NY
Posts: 482
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Z28 with iroc-z Package no.3
Engine: 350TPI
Transmission: 700r4
Axle/Gears: 3.73 posi
Re: turn signal lever swap
Grab it by the base (the part of it that doesnt rotate), push in, and turn CCW about 1/4 turn. It should then pull out, it might take a little wiggling though. The wire for it runs down the column, and plugs in under the dash. Unplug it, pull the old wire out, and fish the new wire down the column, then install the new one.
#6
Junior Member
Join Date: Jul 2008
Location: North Charleston
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Camaro
Engine: 5.7Fl V8 350 tpi
Transmission: 700R4 Automatic
Re: turn signal lever swap
In my camaro it takes some force to make the turn signal go down or up not like u have to pull on it but there is some resistance on it is that normal?
#7
Junior Member
Join Date: May 2008
Location: SSC to UES
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Car: '88 Camaro
Engine: 305 TBI
Re: turn signal lever swap
And is this the procedure for fixing a stuck turn signal? As in, one where the stalk doesn't automatically return when steered straight.
Trending Topics
#9
Member
iTrader: (1)
Join Date: Apr 2008
Location: hudson valley, NY
Posts: 482
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Z28 with iroc-z Package no.3
Engine: 350TPI
Transmission: 700r4
Axle/Gears: 3.73 posi
Re: turn signal lever swap
IS THE PROCEDURE THE SAME ON CAMAROS AS TRANS AMS is what im asking because ive been told i have to remove the lock plate assembly as well
#10
Senior Member
iTrader: (5)
Join Date: Dec 2006
Location: Augusta, Ga
Posts: 2,212
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Trans Am
Engine: 355ci L98 soon to be turbo'd
Transmission: 700R4
Axle/Gears: 2.73 posi
Re: turn signal lever swap
It should be the same procedure for both f-bodies. Both swapping out the lever and swapping out the switch the lever controls inside the column...
Thread
Thread Starter
Forum
Replies
Last Post
Fronzizzle
Suspension and Chassis
6
03-18-2019 08:29 PM