Third Generation F-Body Message Boards

 
Page 1 of 3
1
2
3
Search: Posts Made By: pandorafowler
Showing results 1 to 50 of 138
Search took 0.21 seconds.
Forum: Group Purchases
02-04-2008, 01:09 PM
Replies: 20
Views: 5,850
Posted By pandorafowler

Re: 91-92 Camaro Front Spoiler/Valence

is this still going on?
Forum: Body
10-11-2007, 12:35 PM
Replies: 7
Views: 712
Posted By pandorafowler

Re: GFX questions

I know the 91-92 front spoiler uses tabs to mount on the fenders whereas the 85-90 uses bolt-plates to mount.

19Camaro, do you have any side pics of your car with the 85-90 front with the 91-92...
Forum: Electronics
07-14-2007, 09:12 AM
Replies: 2
Views: 715
Posted By pandorafowler

Re: gauges fuse blows at starting

I hooked a multimeter to the fuse location and found out that during cranking its pulling the voltage down from 11.8 volts to 7.3 volts. I've got the whole dash apart right now and don't see any...
Forum: Electronics
07-12-2007, 06:04 PM
Replies: 2
Views: 715
Posted By pandorafowler

gauges fuse blows at starting

I'm trying to find a short that is blowing the gauge fuse every time I start the engine. It won't blow in the on position but will while cranking. I've tried wiggling wires while in the run...
Forum: Exterior Parts Wanted
05-22-2007, 01:10 PM
Replies: 0
Views: 211
Posted By pandorafowler

wtb 91-92 front spoiler/gfx

Looking for a front chin spoiler/gfx for a 91 camaro here in NC.

dfowler@rwmoore.com
Forum: Exterior Parts Wanted
05-22-2007, 01:09 PM
Replies: 0
Views: 238
Posted By pandorafowler

wtb 91-92 front spoiler/gfx

Looking for a front chin spoiler/gfx for a 91 camaro here in NC.
Forum: Transmissions and Drivetrain
03-26-2007, 01:26 PM
Replies: 6
Views: 482
Posted By pandorafowler

tranny spline question

On a 700r4 from a 91 camaro, is it a 27-spline or 30-spline coming out of the transmission? I counted 27 on mine but just wanted to make sure.
Forum: Transmissions and Drivetrain
03-22-2007, 09:50 PM
Replies: 8
Views: 987
Posted By pandorafowler

Re: What other cars/trucks can i get a 700r4 from

So I could install a 700r4 from a chevy c1500 truck? How hard is it to swap out the tailshafts? Also, what is the truck version's gear ratio's compared to the camaro's?
Forum: Transmissions and Drivetrain
03-21-2007, 06:36 PM
Replies: 2
Views: 548
Posted By pandorafowler

Re: 700r4 rebuild kits

Thanks for the reassurance, I've been searching the past couple of days for reviews of other trannys(bowtie overdrives was one).
Forum: Transmissions and Drivetrain
03-19-2007, 02:09 PM
Replies: 2
Views: 548
Posted By pandorafowler

700r4 rebuild kits

What would be the best rebuild kit for a 91 camaro 700r4? I`m sure that the 3/4 clutches are gone because of it going to neutral after 2/3 shift? This is a daily driver that might see a little bit...
Forum: Tech / General Engine
01-08-2007, 10:52 PM
Replies: 4
Views: 498
Posted By pandorafowler

How would you adjust the bracket? But it is...

How would you adjust the bracket? But it is actually going into fourth at 35. I wonder that the tcc is setup wrong in the chip? Its still the stock coverter for the 305.
Forum: Tech / General Engine
01-07-2007, 10:00 AM
Replies: 4
Views: 498
Posted By pandorafowler

350 swap mph/rpm

I need help to figure out how to lower my rpm/mph ratio. I did a swap from a 305 tbi to a 350 zz4 tpi and my rpms are higher at the same speed with the 350 than it was with the 305. The car goes...
Forum: Tech / General Engine
07-15-2006, 07:01 AM
Replies: 1
Views: 1,318
Posted By pandorafowler

replacement zz3/4 valve springs

I'm having to replace my valvesprings on my engine after the #7 exhaust spring let go and bent the pushrod. I'm trying to figure out what springs to replace the zz3 orange springs with? I have a...
Forum: Body
07-07-2006, 08:33 PM
Replies: 2
Views: 354
Posted By pandorafowler

When I got home from Garner, I could smell it...

When I got home from Garner, I could smell it more underneath the car than from the cap area. The relief valve underneath the car, what happens if it gets clogged?
Forum: Body
07-07-2006, 06:02 PM
Replies: 2
Views: 354
Posted By pandorafowler

filler tube testing

What is the best way to test the filler tube for leaks? I don't know if its the relief that's giving off the fuel smell or if I have a crack in the filler tube.
Forum: Electronics
06-14-2006, 07:24 AM
Replies: 4
Views: 517
Posted By pandorafowler

It turned out to be the ignition switch further...

It turned out to be the ignition switch further down the column had burned out. Looked like it shorted the power lead(big yellow wire) going to the starter relay.
Forum: Electronics
06-12-2006, 09:18 PM
Replies: 4
Views: 517
Posted By pandorafowler

key switch ignition problem

Having a problem starting my 91. Battery is okay,ignition relay is clicking, starter is alright(started car by jumping starter). Car has VATS and has needed me to press the key upward to make the...
Forum: Body
04-05-2006, 06:28 PM
Replies: 3
Views: 558
Posted By pandorafowler

Thanks for the pic,I straightened mine with a...

Thanks for the pic,I straightened mine with a chain comealong enough to put the radiator in so I can drive it to the frame shop hopefully next week.
Forum: Body
02-27-2006, 09:21 AM
Replies: 3
Views: 558
Posted By pandorafowler

Need pics of radiator bar

I need pics of the radiator support/bar that's in back of the nose. I'm trying to get mine straight after a 4wd truck went over my nose and hood. I'm looking for pics on the sides and paralell to...
Forum: Electronics
11-02-2005, 09:53 AM
Replies: 0
Views: 428
Posted By pandorafowler

Alternator

Does anybody know of a alt. that will hook up to the stock wiring harness of a 91 rs but has the holes straight up and down like older alts?
Forum: Parts Wanted 2006
08-19-2005, 10:29 AM
Replies: 0
Views: 347
Posted By pandorafowler

Flowtech Y-pipe

LOOKING FOR A FLOWTECH Y-PIPE THAT SOMEONE WANTS TO GET RID OF.
Forum: Exhaust
08-15-2005, 09:53 AM
Replies: 13
Views: 727
Posted By pandorafowler

What Hedman headers are $200 with the y-pipe? ...

What Hedman headers are $200 with the y-pipe? Part #`s?
Forum: Tech / General Engine
07-14-2005, 04:12 PM
Replies: 6
Views: 2,439
Posted By pandorafowler

Hey Trickster, is there a way to wire it to...

Hey Trickster, is there a way to wire it to remove the buffer box completely? I switched from 305 tbi to 352 tpi w/7730 ecm.
Forum: Electronics
07-12-2005, 06:48 AM
Replies: 0
Views: 447
Posted By pandorafowler

vss buffer box

Do you have to keep the buffer box for the speedo to work? This is a tbi/tpi swap in my 91 rs. I`ve hooked the yellow and purple wires into the 7730 but i unplugged the buffer box and now is...
Forum: TPI
07-07-2005, 03:43 PM
Replies: 5
Views: 676
Posted By pandorafowler

I disconnected the return hose inside the engine...

I disconnected the return hose inside the engine bay and had the pimer connector jumpered. the pump should be pushing 60psi and the afpr was all the way out( afpr mod )
Forum: TPI
07-07-2005, 12:10 PM
Replies: 5
Views: 676
Posted By pandorafowler

brand new walbro. You think it might be the...

brand new walbro. You think it might be the filter clogged up?
Forum: TPI
07-07-2005, 09:12 AM
Replies: 5
Views: 676
Posted By pandorafowler

No fuel in return line

I took my return fuel hose off from the metal line to see if I was having fuel go through the rail system. I have a walbro pump that suppose to be 60psi and had my pressure regulator all the way out...
Forum: TPI
06-25-2005, 09:32 AM
Replies: 1
Views: 677
Posted By pandorafowler

tbi/tpi vats problem

Just did a tbi/tpi swap and the ecm is getting a code 46 for VATS. Supposedly, isn`t vats suppose to diable the fuel pump or does it disable theinjector drivers? I have my pump running and i have...
Forum: TPI
06-22-2005, 01:13 PM
Replies: 11
Views: 656
Posted By pandorafowler

Why did you need to use 3 nuts for?

Why did you need to use 3 nuts for?
Forum: TPI
06-16-2005, 09:54 AM
Replies: 7
Views: 3,434
Posted By pandorafowler

Went and got a noid light and found out my...

Went and got a noid light and found out my injectors were not firing. Idiot me forgot to wire up the injector driver grounds in the ecm connectors. So I got fire to the injectors now but it still...
Forum: TPI
06-14-2005, 12:41 PM
Replies: 7
Views: 3,434
Posted By pandorafowler

But the test lights are like 5 bucks, thats why i...

But the test lights are like 5 bucks, thats why i was asking.
Forum: TPI
06-14-2005, 10:57 AM
Replies: 7
Views: 3,434
Posted By pandorafowler

Noid Light

Can I use a continuity tester instead of a noid light to test and see if my injectors are firing? I`m getting spark, got fuel in the rails, but the f*cker won`t start!
Forum: TPI
06-13-2005, 12:19 PM
Replies: 7
Views: 579
Posted By pandorafowler

Check your rockers also, if they`re still the oem...

Check your rockers also, if they`re still the oem ones.
Forum: TPI
06-13-2005, 09:20 AM
Replies: 3
Views: 463
Posted By pandorafowler

If the brake hose is not connected to the plenum,...

If the brake hose is not connected to the plenum, would that cause it to not start? Also, the map sensor vacumn line, does it need to be a certain size or does it matter?
Forum: TPI
06-13-2005, 06:46 AM
Replies: 3
Views: 463
Posted By pandorafowler

TBI to TPI help

Finished doing the tbi/tpi swap and the engine wont start. I`ve checked the timing to make sure its not 180 off, checked that it was getting spark. How would I go about checking to see if the...
Forum: TPI
05-09-2005, 07:54 AM
Replies: 1
Views: 529
Posted By pandorafowler

tbi to tpi ecm mounting

I`m switching from tbi to tpi and I need to know how to mount the 7730 ecm in place of the stock ecm? Do you use the same bracket or what?
Forum: TPI
04-25-2005, 01:12 PM
Replies: 4
Views: 541
Posted By pandorafowler

new fuel lines

Where can you go to get new tpi fuel lines? Also part numbers would help. These are the lines from the metal lines to the fuel rAIL.
Forum: Cooling
03-28-2005, 07:00 PM
Replies: 2
Views: 522
Posted By pandorafowler

I need to get one with alt bracket holes on the...

I need to get one with alt bracket holes on the passenger side
Forum: Cooling
03-28-2005, 06:23 PM
Replies: 2
Views: 522
Posted By pandorafowler

Older style pump w/ reverse rotation

How hard would it be to change the impeller on a pre-87 pump to a reverse flow water pump? What i need is a water pump with the assesory bolt holes and reverse rotation for a serp. setup? Also,...
Forum: Parts for Sale 2006
03-17-2005, 07:05 PM
Replies: 36
Views: 2,191
Posted By pandorafowler

stock chip

Do you still have the stock chip for it?
Forum: Electronics
03-08-2005, 06:59 PM
Replies: 9
Views: 2,008
Posted By pandorafowler

So you could take the green/white wire and ground...

So you could take the green/white wire and ground it onto the block and it will let the fan run when the engine is switched on?
Forum: TPI
03-01-2005, 06:26 PM
Replies: 3
Views: 449
Posted By pandorafowler

slp 25# injectors

With the slp injectors, do you need to grind down the 4 fuel rail posts for the injectors to seat correctly? Also after that, would you be able to use the clips or not?
Forum: TPI
01-11-2005, 08:01 PM
Replies: 10
Views: 766
Posted By pandorafowler

re: schematic

Yeah, a schematic probably wouldnt be a bad idea, I`m trying to get as many resources as I can just double and triple check myself.
Forum: TPI
01-10-2005, 12:50 PM
Replies: 10
Views: 766
Posted By pandorafowler

So the tbi blue or green injector wire would go...

So the tbi blue or green injector wire would go into the side that says to ecm, is that correct?
Forum: TPI
01-05-2005, 08:11 PM
Replies: 365
Views: 119,993
Posted By pandorafowler

injector connector wiring

For the wiring of the connectors, which side is it positive on the injectors? I`m getting new connectors from work and need to know what side of the injector connects to the green/blue wires
Forum: TPI
01-05-2005, 12:43 PM
Replies: 10
Views: 766
Posted By pandorafowler

I have to wire up the connectors

I have to wire up the connectors
Forum: TPI
01-05-2005, 12:09 PM
Replies: 10
Views: 766
Posted By pandorafowler

injector wiring

I need to find out what side of the injector needs to be connected to wire coming from ecm? I`m switching from tbi to tpi.
Does it matter which side is positive or what.
Forum: TPI
12-18-2004, 10:07 AM
Replies: 4
Views: 2,897
Posted By pandorafowler

the ones that are all orange, not just the tops,...

the ones that are all orange, not just the tops, are 19#ers
Forum: TPI
12-18-2004, 09:21 AM
Replies: 4
Views: 2,897
Posted By pandorafowler

ford orange injectors

What size are the orange injectors off a triton v-10 engine? The numbers of them are

280155917
xl2ec5a

Any guess at what lb/hr these are?

Thanks.
Forum: Transmissions and Drivetrain
10-26-2004, 07:54 PM
Replies: 3
Views: 767
Posted By pandorafowler

how would i do that?

how would i do that?
Showing results 1 to 50 of 138
 
Page 1 of 3
1
2
3


 
Forum Jump


All times are GMT -5. The time now is 02:30 AM.