Third Generation F-Body Message Boards

 
Page 1 of 2
1
2
Search: Posts Made By: squatingeagle
Showing results 1 to 50 of 76
Search took 0.06 seconds.
Forum: Tech / General Engine
08-15-2012, 11:24 AM
Replies: 9
Views: 2,985
Posted By squatingeagle

Re: problem with hot start?

Im having the same problem. It runs great starts just fine except when its hot. i have to let it sit for 10 min then it will start again. I have a new battery and new GM fuel pump. I've done the fuel...
Forum: Auto Detailing and Appearance
03-29-2012, 02:50 PM
Replies: 36
Views: 7,399
Posted By squatingeagle

Re: The good, the bad, and the UGLY! TONS of third gen body kit/ custom pics!!!

why do these people have to pick camaros to ruin?!! Unbelievable
Forum: Aftermarket Product Review
03-28-2012, 01:21 PM
Replies: 27
Views: 8,877
Posted By squatingeagle

Re: Hooker Headers

I have Hooker 2055's ceramic coated. made a noticeable difference and they look great. the y pipe was about 1 inch off so i had to alter it. very nice upgrade the first upgrade anyone should do.
Forum: Body
03-22-2012, 05:41 PM
Replies: 2,141
Views: 354,665
Posted By squatingeagle

Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS

stage20 a few post back showed the car cut up into pieces and taken for scrap. Sad to see that happen. Awesome build Neil, keep up the good work. Keep us posted!!! Good luck
Forum: Suspension and Chassis
10-20-2011, 12:50 PM
Replies: 12
Views: 1,118
Posted By squatingeagle

Re: Vibration?

its was rear wheel bearings. replaced them runs like a dream
Forum: Tech / General Engine
10-20-2011, 12:48 PM
Replies: 36
Views: 1,729
Posted By squatingeagle

Re: Guess My Horsepower!!! :-) Please!

it does. stock L98. Now it has 1.6 rollers and a ram jet 350 cam. and the heads were rebuilt with valve job. havent had the opportunity to dyno yet though.
Forum: Transmissions and Drivetrain
10-18-2011, 04:57 PM
Replies: 63
Views: 23,477
Posted By squatingeagle

Re: My car shakes violently

no i dont believe that will transfer to the steering wheel. check your pitman arm/ steering linkage.
Forum: Wheels and Tires
10-14-2011, 10:58 AM
Replies: 78
Views: 97,698
Posted By squatingeagle

Re: camaro pics with Z06 wheels and wheel specs

i read racing geek did 18x10.5 all around has anyone else done that? i have 4 chrome chrome zo6 18x10.5 and was wondering what your guys' thoughts are for getting them installed. 58mm offset. stock...
Forum: Exterior Parts for Sale
10-14-2011, 10:01 AM
Replies: 1
Views: 513
Posted By squatingeagle

Re: [AZ] zo6 rims

SOLD
Forum: Exterior Parts for Sale
10-13-2011, 04:05 PM
Replies: 1
Views: 513
Posted By squatingeagle

[AZ] zo6 rims

i have 4 18x10.5 rims 58 offset for sale. pickup only. tires are shot the rims are in decent shape with minor scuffs. one rim has a larger nick towards the center asking 400. make an offer and there...
Forum: Exhaust
05-27-2011, 01:21 PM
Replies: 8
Views: 676
Posted By squatingeagle

Re: 2055 y pipe issue

from what ive been reading its sounds like the cause of my problems is because the valves arent adjusted right like you said. also i could be a tooth off on the distributer? could that be a...
Forum: Exhaust
05-27-2011, 12:08 PM
Replies: 8
Views: 676
Posted By squatingeagle

Re: 2055 y pipe issue

im pretty sure that has nothing to do with the engine problems im having...
Forum: Exhaust
05-27-2011, 10:34 AM
Replies: 8
Views: 676
Posted By squatingeagle

Re: 2055 y pipe issue

oh ya it threw a few codes as well. VSS, Prom error and electronic spark advance. when i hooked the computer up to it its BLM's were 108... now i know as much about tuning as my dog does. ill just...
Forum: Exhaust
05-27-2011, 10:10 AM
Replies: 8
Views: 676
Posted By squatingeagle

Re: 2055 y pipe issue

so i finished up the project last night and took it for a drive. my car is extremely powerless! when i pulled the engine i did a cam to i put a cam out of my brothers l98. when i drove it last night...
Forum: Exhaust
05-26-2011, 05:36 PM
Replies: 8
Views: 676
Posted By squatingeagle

2055 y pipe issue

I just installed 2055hkr's. Install went well no problems till i got to the y pipe that hooker sent with the headers. when i got one of the flanges in place to mount to the header, the other one was...
Forum: Exhaust
05-26-2011, 11:49 AM
Replies: 291
Views: 78,739
Posted By squatingeagle

Re: Those with Hooker 2055's, come on in!

just installed my 2055hkr's this last week. pulled the engine to do it so i had plenty of clearance piece of cake. got it all back in and noticed a huge problem... the y pipe that came with them...
Forum: Tech / General Engine
05-25-2011, 03:18 PM
Replies: 36
Views: 1,729
Posted By squatingeagle

Re: Guess My Horsepower!!! :-) Please!

we just dyno'd my brothers B4C L98 with 160000. it hit 222rwhp all stock except for cat back. the engine was rated for 245 from factory (its a '92). food for thought
Forum: Cooling
04-29-2011, 02:41 PM
Replies: 20
Views: 20,698
Posted By squatingeagle

Re: How to change the thermostat?

why did you order the gasket? just curious. autozone or just about every other shop has one for about a buck. good luck with the swap its really easy.
Forum: Cooling
04-29-2011, 02:36 PM
Replies: 11
Views: 985
Posted By squatingeagle

Re: Overheating

go one step further and buy 4th gen cooling fans off a 98-02 ls1. you will never ever ever....ever over heat again. ive done this mod on 3 of my camaros. the best thing you could ever do to your car
Forum: Engine/Drivetrain/Suspension Parts for Sale
04-18-2011, 10:15 AM
Replies: 29
Views: 1,837
Posted By squatingeagle

Re: FOR SALE: PERFORMANCE PARTS, 2055'S, MSD, BBK, B&M,ACCEL, MOROSO

i want the headers and y if you still got them. and they still have the air tubes right? how much shipped to 85204? thanks
Forum: Transmissions and Drivetrain
03-20-2011, 12:02 AM
Replies: 63
Views: 23,477
Posted By squatingeagle

Re: My car shakes violently

it was bearings. replaced both rear wheel bearings and its amazing. my car has never driven so smooth
Forum: Transmissions and Drivetrain
03-19-2011, 11:59 PM
Replies: 18
Views: 9,001
Posted By squatingeagle

Re: Driveline Vibration Help

finished the bearings. rides like a dream apart from the 20 years/170xxx. didnt have any leaks. but when i got the passenger bearing out it had a bent cage. new bearings and axle shafts my car has...
Forum: Transmissions and Drivetrain
03-19-2011, 11:56 PM
Replies: 17
Views: 2,260
Posted By squatingeagle

Re: Vibrations (at approx ~70mph.. detailed info inside)

finished up a few hours ago rides like a dream now. except that its 20 years old with 170xxx on it. bearings did the trick sure enough got one out and it had a bent cage. anthony714 if you hit...
Forum: Transmissions and Drivetrain
03-18-2011, 12:54 PM
Replies: 20
Views: 2,153
Posted By squatingeagle

Re: Nasty Vibration...

knight 123 most likely it the rear wheel bearing. that gm service manual says vibration in the axle is caused by a rough rear wheel bearing
Forum: Transmissions and Drivetrain
03-18-2011, 11:15 AM
Replies: 18
Views: 9,001
Posted By squatingeagle

Re: Driveline Vibration Help

not the whole assembly sliding in and out but the top and bottom rocking in and out. or even any up and down indicates a worn bearing
Forum: Transmissions and Drivetrain
03-18-2011, 10:32 AM
Replies: 18
Views: 9,001
Posted By squatingeagle

Re: Driveline Vibration Help

check your rear wheel bearings. Strawboss, you said that was one of the things you didnt replace when you did your axle. replace them. gm service manual says vibration in the year is caused by rough...
Forum: Transmissions and Drivetrain
03-18-2011, 10:23 AM
Replies: 17
Views: 2,260
Posted By squatingeagle

Re: Vibrations (at approx ~70mph.. detailed info inside)

another way to check if bearings are bad is to grab your rotor top and bottom and try to pry/pull in and out. you should get NO play. if any your bearings are worn out.
Forum: Transmissions and Drivetrain
03-18-2011, 10:22 AM
Replies: 17
Views: 2,260
Posted By squatingeagle

Re: Vibrations (at approx ~70mph.. detailed info inside)

i have the vibration at 70 and everything past. ive replaced drive shaft, u joints, axle shafts and tires. i dont have bent rims. gm service manual says rough rear wheel bearing. im going to run the...
Forum: Suspension and Chassis
03-18-2011, 10:14 AM
Replies: 12
Views: 1,118
Posted By squatingeagle

Re: Vibration?

service manual says its a rough rear wheel bearing. ive got the same problem right now. ive replaced the drive shaft, u-joints, axle shafts, and tires. i dont have bent rims and ive got a gm trans...
Forum: Transmissions and Drivetrain
03-18-2011, 10:10 AM
Replies: 63
Views: 23,477
Posted By squatingeagle

Re: My car shakes violently

at 70 and past it vibrates really bad. its not noise its for sure a vibration. didnt have it in my last 2 axles and now i do in this one. ill pull the diff cover today and run it without axle shafts...
Forum: Transmissions and Drivetrain
03-17-2011, 10:50 PM
Replies: 63
Views: 23,477
Posted By squatingeagle

Re: My car shakes violently

whats the latest news? got the same problem i replaced both axle shafts and swapped out the drive shaft. check your rear wheel bearings for play by grabbing the rotor top and bottom and try to ...pry...
Forum: Engine/Drivetrain/Suspension Parts for Sale
03-09-2011, 06:41 PM
Replies: 12
Views: 1,105
Posted By squatingeagle

Re: hooker headers

pm sent
Forum: Engine/Drivetrain/Suspension Parts for Sale
03-03-2011, 12:53 PM
Replies: 12
Views: 1,105
Posted By squatingeagle

Re: hooker headers

interested if still available
Forum: Engine/Drivetrain/Suspension Parts for Sale
10-08-2010, 01:42 PM
Replies: 7
Views: 1,798
Posted By squatingeagle

Re: 3rd gen to ls1 front brake conversion bracket

id be interested as well. let us know how it goes
Forum: Interior
10-08-2010, 11:18 AM
Replies: 9
Views: 911
Posted By squatingeagle

Re: Put in headliner myself or take it somewhere...

I re-fiberglassed mine and glued new headliner fabric to it. peace of cake. you can totally do it yourself. buying fabric and 3m glue was like 25 bucks then 20 more on a fiberglass kit at autozone.
Forum: Body
10-08-2010, 11:08 AM
Replies: 22
Views: 1,267
Posted By squatingeagle

Re: DOes this Hood look Weird to you?

Agreed.
Forum: Tech / General Engine
09-02-2010, 04:29 PM
Replies: 1
Views: 1,467
Posted By squatingeagle

Re: LB9 TPI Cam Swap

i think im going with the lt4 cam. that seems to be the best one for a stock motor. thanks guys.
Forum: Engine/Drivetrain/Suspension Parts for Sale
09-02-2010, 01:11 PM
Replies: 15
Views: 1,063
Posted By squatingeagle

Re: Hotcam and Coated 2055 Hookers

no cant say i do know him. cant recall seeing a purple rs either. so is that 325 for the headers, y, and cat? how much without the cat? or is it a group price. and the headers are ceramic coated?
Forum: North East Region
09-02-2010, 12:53 PM
Replies: 65
Views: 4,021
Posted By squatingeagle

Re: $500 drag racing ticket??...

holy crap lighten up grandpa! grow up? haha wow.

congrats on getting off your ticket. that cop was a prick. not enough evidence to support his claims then he fills the ticket out wrong? well...
Forum: Engine/Drivetrain/Suspension Parts for Sale
09-02-2010, 11:57 AM
Replies: 15
Views: 1,063
Posted By squatingeagle

Re: Hotcam and Coated 2055 Hookers

does the headers come with the y pipe?
Forum: LTX and LSX
09-02-2010, 11:51 AM
Replies: 85
Views: 13,035
Posted By squatingeagle

Re: 420 rwhp / 407 ft-lb Dyno Sheet & Video inside *Now with 10 bolt carnage!*

sorry about the blow out. nice build though keep it goin
Forum: Tech / General Engine
09-02-2010, 10:59 AM
Replies: 8
Views: 692
Posted By squatingeagle

Re: new cam install problem! help quick!

"for lt1 or l98 engines (pre 1996) the dowel pin in the end of the camshaft must be pushed in so extension from end of cam is .30"+-.01". for 1996 lt1 and lt4 engines, the dowel pin is in the correct...
Forum: Tech / General Engine
09-01-2010, 05:23 PM
Replies: 1
Views: 1,467
Posted By squatingeagle

LB9 TPI Cam Swap

i've been reading up on a cam swap and ive read so many options that i would like a little more knowledge before i spend the money. i have a stock 91 305 tpi without G92. Accel intake and runners...
Forum: TPI
07-01-2010, 03:08 PM
Replies: 4
Views: 850
Posted By squatingeagle

Re: High idle on lb9 5 speed

check the vacuum line that comes out of the brake booster i believe it goes straight into the plenum. check it for leaks/splits or the o ring on the brake booster might be bad. had it happen to me...
Forum: History / Originality
07-01-2010, 02:53 PM
Replies: 5
Views: 837
Posted By squatingeagle

Re: 91 z28 worth buying?

its a third gen camaro of course its not worth it! that being said of course i would buy it :) its got enough of the "rarer" options that would convince me. like t tops and the factory cd player. i...
Forum: Tech / General Engine
07-01-2010, 02:48 PM
Replies: 7
Views: 1,180
Posted By squatingeagle

Re: Hot cam in a 355 TPI

so is the hot cam with 1.5:1 rockers compatible?
Forum: Aftermarket Product Review
06-22-2010, 04:47 PM
Replies: 49
Views: 6,751
Posted By squatingeagle

Re: Spohn Wonderbar disappointment.

thats cool that spohn gave you most of your money back. i still will go with umi from now on.
Forum: Tech / General Engine
06-15-2010, 12:56 PM
Replies: 16
Views: 17,999
Posted By squatingeagle

Re: 205 or 230 hp lb9.. which do I have?

its the 205 hp. it my car exactly. single cat 110 gauges 5 speed and 3.08 rear. g92 got the 145 gauges dual cats and the 230 hp rating with 3.42 rear.
Forum: Tech / General Engine
06-15-2010, 12:48 PM
Replies: 12
Views: 1,883
Posted By squatingeagle

Re: 305 tpi w/t5. Want to rebuild/get more hp

t56 out of a 93-97 f body car will bolt up to your lb9. all you need is the t56 clutch, flywheel, bell housing, starter, slave cylinder and a new tranny cross member
Showing results 1 to 50 of 76
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -5. The time now is 02:08 PM.