i need HELP! car wont crank
#1
i need HELP! car wont crank
I have a 86 iroc z 305 tpi that won't start Wen I turn the key I can gear the fuel pump engage but when I turn the key nothing happens the starter won't crank click or anything n I took the starter out and had it tested but it passed and the guy from autozone told me to have the cylinoid checked I was wondering Wat else might be the problem? So please help me I need to fix it fast
#3
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: i need HELP! car wont crank
bad connection. does you key have a little black pellet chip in it? your vehicle anti theft system might have malfunctioned. if you go to the wiring harness loom by the brake master cylinder you can pull out a bigger purple and red wires. jump the wires together and see if it cranks the car. the key will need to be on and in park w/parking brake set for safety reasons. other then that your neutral safety switch could be acting up. does the car start in neutral? or in another gear? again be sure to hold your foot on the brake. that's where i'd go.
and also i have seen plenty of starters pass the bench test and not work on the car
and also i have seen plenty of starters pass the bench test and not work on the car
#5
Re: i need HELP! car wont crank
bad connection.b does you key have a little black pellet chip in it? your vehicle anti theft system might have malfunctioned. if you go to the wiring harness loom by the brake master cylinder you can pull out a bigger purple and red wires. jump the wires together and see if it cranks the car. the key will need to be on and in park w/parking brake set for safety reasons. other then that your neutral safety switch could be acting up. does the car start in neutral? or in another gear? again be sure to hold your foot on the brake. that's where i'd go.
and also i have seen plenty of starters pass the bench test and not work on the car
and also i have seen plenty of starters pass the bench test and not work on the car
#6
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: i need HELP! car wont crank
but did the car get the whole vats system? doubtful. probably not your problem. did you test your battery and ensure the connections on them were good, clean, tight?
Trending Topics
#8
Member
Join Date: Aug 2008
Location: Eastern Ohio!
Posts: 259
Likes: 0
Received 1 Like
on
1 Post
Car: Mystifying 1989 TBI Camaro.
Engine: 1992 350 Truck Engine. TBI
Transmission: 700R4 when it wants to be.
Axle/Gears: 2.73
Re: i need HELP! car wont crank
Did you make sure the connector on the column that has the rod running to it was correct? You could try swapping it (it's a switch) with your old one. I think it only has two screws/bolts holding it on, but it's been awhile since I changed my column, so I could be wrong.
Couldn't hurt to check it.
Couldn't hurt to check it.
#9
Re: i need HELP! car wont crank
Did you make sure the connector on the column that has the rod running to it was correct? You could try swapping it (it's a switch) with your old one. I think it only has two screws/bolts holding it on, but it's been awhile since I changed my column, so I could be wrong.
Couldn't hurt to check it.
Couldn't hurt to check it.
Thread
Thread Starter
Forum
Replies
Last Post