Replacing shift knob in 89
Supreme Member
iTrader: (2)
Joined: Jan 2001
Posts: 4,149
Likes: 3
From: Tampa, FL, USA
Car: 93 240SX
Engine: LQ9
Transmission: T56
Axle/Gears: 3.54 R200 IRS
Originally posted by mike83z-28
Anyone know how to get an automatic shift **** out of an 83 by any chance?
Mike
Anyone know how to get an automatic shift **** out of an 83 by any chance?
Mike
Front
---
| |
| |
Rear
Trending Topics
Supreme Member
iTrader: (17)
Joined: Feb 2003
Posts: 2,182
Likes: 1
From: Buckley AFB, CO / Crestview, FL
Car: 83 Z-28
Engine: LG4
Transmission: 700R4
Axle/Gears: 02 WS6 Rear w/3:42
Ok, how do you get the button off? What I am doing is replacing the old **** with one in better condition. I just want to make sure I don't break anything. Thanks.
Mike
Mike
Shift ****-
I have ran into two syles-
1 the clip is in the front of the shifter **** and is U shaped you simply pry it out and the **** comes out all together.
2. the button must be pulled off (simply grasp with hand and pull up) and under the button is a C clip which you remove and the **** body comes off.
1 the clip is in the front of the shifter **** and is U shaped you simply pry it out and the **** comes out all together.
2. the button must be pulled off (simply grasp with hand and pull up) and under the button is a C clip which you remove and the **** body comes off.
Supreme Member
iTrader: (17)
Joined: Feb 2003
Posts: 2,182
Likes: 1
From: Buckley AFB, CO / Crestview, FL
Car: 83 Z-28
Engine: LG4
Transmission: 700R4
Axle/Gears: 02 WS6 Rear w/3:42
Just got back from trying to replace the ****. My 83 had the type where you have to pull the button off then you have to remove the C clip. The C clip is a little tricky to get off. After I had the **** off and tried to put the one I got from a junkyard on, it would not fit because it only had one tab and it was wider that the ones on my 83
Oh well, at least I know how to remove everything now. All I have to do is go back and get one similiar to mine. Thanks for all the help.
Mike
Oh well, at least I know how to remove everything now. All I have to do is go back and get one similiar to mine. Thanks for all the help.
Mike
Supreme Member
Joined: Feb 2003
Posts: 1,473
Likes: 0
From: chesapeake va
Car: 08 Sierra, 08 Silverado, 91 z28
Engine: 5.3, 4.3, 5.7
Transmission: autos
Originally posted by JAKEDPLAYA
is there anyway that someone could get that hammerhead B&M shifter handle onto stock 89 auto shifter????
is there anyway that someone could get that hammerhead B&M shifter handle onto stock 89 auto shifter????
Supreme Member
Joined: Feb 2003
Posts: 1,473
Likes: 0
From: chesapeake va
Car: 08 Sierra, 08 Silverado, 91 z28
Engine: 5.3, 4.3, 5.7
Transmission: autos
try some vise grips, or maybe a pipe wrench, but it does screw off, i had a 85 with a manual and it was hard to get off but did come off
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
May 10, 2023 07:19 PM




