[ON] 9 Bolt Axles Partout
Thread Starter
Joined: Jun 2002
Posts: 722
Likes: 6
From: Ottawa, Ontario
Car: 86 IROC
Engine: LQ4 6.0L
Transmission: T56
Axle/Gears: 3.55 8.8
9 Bolt Axles Partout
See details below - Post #8
Last edited by 6speedIROC; Oct 29, 2015 at 08:48 AM.
Thread Starter
Joined: Jun 2002
Posts: 722
Likes: 6
From: Ottawa, Ontario
Car: 86 IROC
Engine: LQ4 6.0L
Transmission: T56
Axle/Gears: 3.55 8.8
Re: 9 Bolt Axle with 4.10 Gears
Going to part this out in November along with 3 other 9 bolts with 3 series carriers.
Junior Member
iTrader: (1)
Joined: May 2012
Posts: 63
Likes: 0
From: Milwaukee, WI ; San Bernardino, CA
Car: 1991 Camaro RS
Engine: 305 will be LSX eventually
Transmission: T56
Axle/Gears: Borg Warner
Re: 9 Bolt Axle with 4.10 Gears
I'd be interested in just the gears sets you have if any of them are 3.7 or numerically higher. Come November if you decide to part them out, PM me if you decide to do that.
Junior Member
Joined: Nov 1999
Posts: 33
Likes: 0
From: Jacksonville, Fl
Re: 9 Bolt Axle with 4.10 Gears
Complete 9 bolt Borg Warner axle with 4.10 gears.
Fully rebuilt about 2,000 miles ago with all new bearings & seals & longer studs.
TA Performance cast aluminum rear cover (pre-loads main bearing caps).
Ratech solid pinion spacer.
Housing has lower control arm relocation brackets installed/welded on.
Posi is fully shimmed and works beautifully.
Comes with backing plates for single piston rear disk, no calipers, disks, or brake lines included.
This axle will bolt into any thirdgen with no modifications.
Will crate axle if shipped.
Located in Ottawa, Canada.
Shipping extra - approx $200 via freight to almost any USA.
Fully rebuilt about 2,000 miles ago with all new bearings & seals & longer studs.
TA Performance cast aluminum rear cover (pre-loads main bearing caps).
Ratech solid pinion spacer.
Housing has lower control arm relocation brackets installed/welded on.
Posi is fully shimmed and works beautifully.
Comes with backing plates for single piston rear disk, no calipers, disks, or brake lines included.
This axle will bolt into any thirdgen with no modifications.
Will crate axle if shipped.
Located in Ottawa, Canada.
Shipping extra - approx $200 via freight to almost any USA.
How much for the rear axle?
Trending Topics
Thread Starter
Joined: Jun 2002
Posts: 722
Likes: 6
From: Ottawa, Ontario
Car: 86 IROC
Engine: LQ4 6.0L
Transmission: T56
Axle/Gears: 3.55 8.8
Re: 9 Bolt Axle with 4.10 Gears
GEARS & BEARINGS:
-370 NEW IN BOX GM9-370 Motive gears ($225 new) $175 [SEE OTHER POST FOR DETAILS https://www.thirdgen.org/forums/engi...lt-3-70-a.html
-Complete NEW IN BOX Master Install kit (have 2) - Motive R7.75RMKT ($162 new) $100 (Timken carrier and pinion bearings, carrier and pinion shims, bolts, rtv, marking compound)
-327 used gears $40
-410 used gears $150 [SOLD]
AXLES:
-Axles - $50 pair with bearings & seals & retainers (have 3 pairs, plus one other, not sure what side) [SOLD 2 PAIR & EXTRA - 1 PAIR LEFT] - shpping is about $40 for a pair
DISC BACKING PLATES:
-Backing plates for single piston disk brakes - $40 pair (3 pairs, 2 with dust shields, 1 without) [SOLD 1 PAIR - 2 PAIR LEFT]
POSI CARRIERS:
-'3' Series Carriers $200 with tight posi cones, lots of wear left (have 3) [ALL SOLD]
STUD GIRDLE:
-TA Performance Rear End Girdle with optional ARP studs $125 [http://www.taperformance.com/proddet...?prod=TA_1802] [SOLD]
HOUSINGS:
-2 housings with lower control arm relocation brackets welded on - offers [SOLD 1, 1 LEFT]
-370 NEW IN BOX GM9-370 Motive gears ($225 new) $175 [SEE OTHER POST FOR DETAILS https://www.thirdgen.org/forums/engi...lt-3-70-a.html
-Complete NEW IN BOX Master Install kit (have 2) - Motive R7.75RMKT ($162 new) $100 (Timken carrier and pinion bearings, carrier and pinion shims, bolts, rtv, marking compound)
-327 used gears $40
-410 used gears $150 [SOLD]
AXLES:
-Axles - $50 pair with bearings & seals & retainers (have 3 pairs, plus one other, not sure what side) [SOLD 2 PAIR & EXTRA - 1 PAIR LEFT] - shpping is about $40 for a pair
DISC BACKING PLATES:
-Backing plates for single piston disk brakes - $40 pair (3 pairs, 2 with dust shields, 1 without) [SOLD 1 PAIR - 2 PAIR LEFT]
POSI CARRIERS:
-'3' Series Carriers $200 with tight posi cones, lots of wear left (have 3) [ALL SOLD]
STUD GIRDLE:
-TA Performance Rear End Girdle with optional ARP studs $125 [http://www.taperformance.com/proddet...?prod=TA_1802] [SOLD]
HOUSINGS:
-2 housings with lower control arm relocation brackets welded on - offers [SOLD 1, 1 LEFT]
Last edited by 6speedIROC; Nov 2, 2015 at 11:57 AM.
Thread Starter
Joined: Jun 2002
Posts: 722
Likes: 6
From: Ottawa, Ontario
Car: 86 IROC
Engine: LQ4 6.0L
Transmission: T56
Axle/Gears: 3.55 8.8
Re: 9 Bolt Axles Partout
Still have the 3.70 motive gears and install kit..NEW IN BOX.
Make me an offer!
Make me an offer!
Thread Starter
Joined: Jun 2002
Posts: 722
Likes: 6
From: Ottawa, Ontario
Car: 86 IROC
Engine: LQ4 6.0L
Transmission: T56
Axle/Gears: 3.55 8.8
Re: 9 Bolt Axles Partout
I may have an axle left, but that's about all. What are you looking for?
Thread
Thread Starter
Forum
Replies
Last Post
hectre13
Engine/Drivetrain/Suspension Parts for Sale
2
Dec 11, 2023 08:14 AM
ambainb
Camaros for Sale
11
Apr 25, 2016 09:21 PM
hectre13
Engine/Drivetrain/Suspension Parts for Sale
7
Aug 26, 2015 08:17 AM
Dialed_In
Firebirds for Sale
2
Aug 20, 2015 01:45 PM