ECM Programs wanted - Third Generation F-Body Message Boards


South West Region South West regional discussion board.

ECM Programs wanted

Reply
 
Thread Tools Search this Thread
Old 07-11-2018, 09:41 AM   #1  
Junior Member
Thread Starter
 
Join Date: Dec 2006
Posts: 26


ECM Programs wanted

I am looking for the Stock running (memcal) PROGRAM for a 80s 350 with TPI with MAF and for a 93 Chevy van running a 16168625/16186695 ECM. The ones you can load into a laptop and run the van from IT and then using TunerPro adjust on the fly. The van is needed now to try and improve both its MPG (10/14) and performance if possible. I hope to switch the 93 Chevy Van from TBI to TPI this winter, which I have two set ups with MAFs, one from a Camaro and the other from a Corvette. These are in storage so cannot get their ECM numbers. And or: Any local Phoenix shop doing these older OBDI systems, and can burn a new chip?? Or any program running the Lean Burn Cruse settings or how to turn them on?? Thanks. Rich Farther information to clear up some misunderstandings: I am trying to do this in stages…first stage as I am CURRENLY running the Stock 93 Chevy Van 5.7 350 computer driving a TBI system, I was trying to improve ITS MPG until we get into cooler temps like out winter this Halloween, then I am considering a TPI with either the original PCM or a 95 LS PCM with its tranny control and better one at a time injector system..and yes I know about opt-spark. Later I plan on getting a 6L80E transmission (Or a 8L90E IF it can be used...)with a control computer for it and a rebuilt rear end with possi and a TALL 2.20:1 gear ratio. Rich

Last edited by racprops; 07-11-2018 at 03:28 PM.
racprops is offline   Reply With Quote
Old 07-11-2018, 11:02 AM   #2  
Sponsor
iTrader: (79)
 
Tuned Performance's Avatar
 
Join Date: Dec 2004
Location: Mile High Country !!!
Posts: 10,289
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt


Re: ECM Programs wanted

Here is a memcal for your 625 ecm , sounds like your looking for a memcal for a 1227165 ecm ?
6e mask has hwy mode but also have vats that needs to be programmed out.
I have a few options if you send me a pm and I can do reprogramming.
https://m.ebay.com/itm/16168625-BDJY...pe!90011!US!-1

Last edited by Tuned Performance; 07-11-2018 at 02:55 PM.
Tuned Performance is offline   Reply With Quote
Old 07-11-2018, 03:32 PM   #3  
Junior Member
Thread Starter
 
Join Date: Dec 2006
Posts: 26


Re: ECM Programs wanted

Or the newer 8 Speed 8l90e: 6L80E Gear ratios: 1St: 4.484 2nd 2.872 3rd. 1.842 4Th. 1.141 5th. 1.00 6th. 0742 8L90e Gear Ratios… 1st. 4.56 2nd. 2.97 3rd. 208 4th. 1.69 5th. 1.27 6th. 1.00 7th. 0.85 8th.0.65

Last edited by racprops; 07-11-2018 at 03:41 PM.
racprops is offline   Reply With Quote
Old 07-11-2018, 03:34 PM   #4  
Junior Member
Thread Starter
 
Join Date: Dec 2006
Posts: 26


Re: ECM Programs wanted

Damn it I hate how this system takes out all spacing and formating,....I had very nice layout for those numbers...as a run on sentence it is a mess. Rich

Last edited by racprops; 07-11-2018 at 04:22 PM.
racprops is offline   Reply With Quote
Old 07-11-2018, 03:53 PM   #5  
Sponsor
iTrader: (79)
 
Tuned Performance's Avatar
 
Join Date: Dec 2004
Location: Mile High Country !!!
Posts: 10,289
Car: 1967 Camaro, 91 z28
Engine: Lb9
Transmission: M20
Axle/Gears: J65 pbr on stock posi 10bolt


Re: ECM Programs wanted

For the oem ecm you should look at pro thread
https://www.thirdgen.org/forums/tpi/...p-305-tbi.html
As far as hwy mode for the factory ecm you should ask tunercat to see if it can be enabled.
Or piggyback the factory ecm with a 165 ecm. The ecm needs a vss signal a Dakota digital sgi-5 might be the answer for that.
Tuned Performance is offline   Reply With Quote
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
laptop programs compatable with V6 ecm coolrimsatleast DFI and ECM 2 12-19-2006 10:21 PM
problems with some programs connecting to ecm. TraviZ DIY PROM 2 09-04-2006 04:07 PM
ATTN: guys with the desktop dyno programs grouper V6 1 08-15-2001 09:08 PM
Difference btw 'Vette and F-Body programs Greg '85 T/A DIY PROM 13 07-22-2001 11:31 AM
chip programs. Greg90iroc DIY PROM 19 04-17-2001 06:53 PM


Go Back   Third Generation F-Body Message Boards >

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Advertising
Featured Sponsors
Vendor Directory

1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 05:48 AM.


All content copyright © 1997 - 2018 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: