ses light supposed to flash like this at ignition?
#1
Supreme Member
Thread Starter
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
ses light supposed to flash like this at ignition?
http://www.youtube.com/watch?v=Dyoodmsbozk
its blinks like this when i turn the ignition on...
is it supposed to do this? i dont remember it doing this before and my car wont stay running..
when i put it in gear, it wants to die and it idles high in park or neutral.
been trying to figure it out here...
https://www.thirdgen.org/forums/tpi/...ll-when-4.html
its blinks like this when i turn the ignition on...
is it supposed to do this? i dont remember it doing this before and my car wont stay running..
when i put it in gear, it wants to die and it idles high in park or neutral.
been trying to figure it out here...
https://www.thirdgen.org/forums/tpi/...ll-when-4.html
#2
Supreme Member
iTrader: (17)
Re: ses light supposed to flash like this?
Normally the light would be on when the key is switched to the on position prior to cranking. Now once the the car turns on, it may flash and stay off. But if it stays onafter it turns on, then there is an error stored in the MemCal. Now if the light turns off while driving, then the error is intermittant, (faulty sensor that just began to work properly). Most sensors have a refference voltage of IIRC, .10 - 5.0 volts. If the voltage is out of that range, the ECM will sense it and record the troublecode to that sensor. I have a book that has a good explaination of troublecodes for the TPI if your interested. PM me.
#4
Supreme Member
Thread Starter
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: ses light supposed to flash like this?
rancho cucamonga
thats just it though! it wont even throw the intitial code 12. its like, dead. lol..
thats why i think its the ecm...
thats just it though! it wont even throw the intitial code 12. its like, dead. lol..
thats why i think its the ecm...
#5
Supreme Member
Thread Starter
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: ses light supposed to flash like this?
and i know nothing about all the MemCal and PROM tuning stuff...lol
#6
Senior Member
Join Date: Dec 2009
Location: Toronto
Posts: 517
Likes: 0
Received 1 Like
on
1 Post
Car: '88 Trans Am GTA
Engine: 305 TPI
Transmission: 700R4
Re: ses light supposed to flash like this?
If it's flashing while the engine is running the computer is sensing that there is an issue that can cause damage to the engine or emmision control devices (most likely to cat). The flashing is to get your attention so you STOP driving the car.
#7
Supreme Member
Thread Starter
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: ses light supposed to flash like this?
it only flashes on igniton..when i start it, it goes away..
but it does the weird fan thing after i come back to it hours later after driving it before..
but it does the weird fan thing after i come back to it hours later after driving it before..
Trending Topics
#8
Supreme Member
Thread Starter
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: ses light supposed to flash like this?
i think i remember it being solid before when i turned the ignition on...
dont think this is normal.
dont think this is normal.
Thread
Thread Starter
Forum
Replies
Last Post
Hellbillydeluxe
Tech / General Engine
10
09-22-2015 09:58 PM
eightsixseven
Tech / General Engine
1
08-14-2015 03:09 PM