Selling my whole set-up as I bought another car and
Will not be continuing with my other one for a while.
Everything in the picture is included as well as things not included in the picture.
PLEASE read what’s included before asking me if it is or not, some parts are not pictured.
I have listed what parts you will need to have a fully running engine also.
The wiring harness was modified by me(3rd time I’ve done this) and is now a fully stand alone harness, all unnecessary wires have been removed. All hook-up wires are fully label for an easy install. A/C was removed but I can reconnect the wires needed for it, if asked to. VATS has not been removed on the computer.
I am looking to get my moneys worth for this set-up/time and parts put into it
And also a local buyer – I will start my price at $3100
Any OTHER question anyone needs answering, call me at 281-413-4582 on my cell
I am located in Cypress TX 77429
I will not separate so please don’t ask

Included:
2000 engine block w/ 86k
2002 241 vette heads with vavle job, new seals, installed with all new bolts and metal head gaskets
2000 T-56 transmission with clutch/flywheel assembly w/86k
2000 modified wiring harness, all unnecessary wires removed, can make it w or wo A/C
2000 stock computer, manual trans
Low mile 18K stock springs and rockers
New GM high performance lifters
New LS2 water pump with gaskets
New LS6 oil pump
New LS2 timing sprockets and chain
stock hurst shifter w/ 6-speed white shifter ball
Starter
Stock balancer pulley
Valve covers
Alt bracket
A/C bracket
Trans mount and crossmember
Oil pan w/ pickup tube and tray
Coil packs and brackets
Fuel lines
Injectors
LS1 intake
LS1 Steam crossover pipe
Throttle body and sensors
Cam, thermostat, oil level sensors
Bolts bolt bolts

Parts you will need to make it run:
Pushrods
Injector ring seals
Alternator
A/C compressor


Parts I can also provide:
255lb walbro inline fuel pump with all needed fittings
clutch slave fitting in to a 3an Stainless steel line
3" in/out flowmaster y pipe
Autometer C2 gauges: tach, speedo, fuel, oil pre, water temp.
Dynomax welded race muffler 3" in/out

JR

 

if only you were selling this in a few months, I'd be all over it..
well if you still have it by next march..aggh its hopeless, Im sure you'll sell it by then..
Good luck on your sale and sorry for my small rant
-Fernando

 

I've been trying to sell it for a few months now just over on LS1tech, just decided to post it here to see if i could get any bites.
Anyways I hope I can sell it soon too, as my DD need desperate attention and this would fix her right up.

Cheers, JR

 

Lowering price to $2900.
Had to use the oil pan off this motor as I found out the one on my Trans am was cracked badly. still comes with the pick-up tube and tray.

Would like to sell it this month peeps

JR

 

More problems, My DD Trans Am's Tranny just lost 3rd and 4th gear, damn autos , I will be using this manual tranny for the swap.
I will sell the motor with wiring and comp for $2000.
and if you want I can throw in a 4l60e that needs to be rebuilt with a lightly used Yank SS 3600 stall ($1000 new) for $550
Also if you buy the motor I will have the computer's VATS deleted, rear O2's deleted, and retuned and wire the harness for an automatic if you wish. all your choice guys.

Hurting for cash, PM ME NOW!! , JR

 

Offers?

 

Man I sure wish I had the money...I only got a couple hundred to my name so I can't offer any resonable offer yet...good luck with a sale though

Ps. What side of Houston do you live in?

 

I'm on the Northwest side of Houston, in Cypress 77429 .

Got anything to trade?
looking for TA LS1 parts:
Double adjustable LCA
subframe connectors
spec stage 3 clutch
spec flywheel

Also like laptops and digital camcorders

It's so close to Christmas, I really want to sell this thing

 

sorry man Ive got pretty much nothing to trade..Ive got a camcorder and thats about it...

 

u ever sell that motor?

 

Nope still have it lol

 

pm sent

 

????

 

did you go ahead and used the tranny for your trans am?