decking - Third Generation F-Body Message Boards - Threads Tagged with decking

Third Generation F-Body Message Boards
Tags
Threads Tagged with decking

Threads Tagged with decking

Thread / Thread Starter

Last Post

Replies

Views

Forum

air, alignment, back, block, carburetor, check, decked, decking, gap, gaskets, head, indian, intake, leaks, shelack

6 Attachment(s)

Can't get Air Gap intake to seal

(

Multi-page thread

1 2 3)

LilJayV10 on 09-17-2008

06-24-2018 07:31 PM
by NoEmissions84TA

Go to last post

28,145

0045, 350, block, calculate, chevy, compression, corvette, deck, decked, decking, deckingasmallblock, engine, height, l98, ratio

350 Deck height

grx45 on 06-09-2013

06-11-2013 06:02 PM
by Ingram78

Go to last post

5

1,228

1178vc, blew, blown, common, compressed, decking, gasket, gen, head, headgasket, heads, reinz, ta, thickness, times, victor

blown head gasket (third time)

cvdfj on 07-10-2012

07-11-2012 06:25 PM
by cvdfj

Go to last post

8

2,123

Tech / General Engine

350, block, bored, car, checking, deck, decked, decking, engine, figure, find, machine, motor, number, stamp, teel

How can you tell if a block deck has been cut?

lunaticinaZ on 03-15-2011

03-16-2011 07:49 AM
by lunaticinaZ

Go to last post

4

11,784

Tech / General Engine

decking, gained, heads

How much can you deck 305 lb9 heads.

redfbody on 07-28-2009

07-29-2009 03:21 PM
by redfbody

Go to last post

2

429

Tech / General Engine

30, block, change, cubic, decking, inches, thousandths

less cubic inch with decking

mpb74 on 02-13-2009

02-14-2009 09:45 PM
by skinny z

Go to last post

8

865

Tech / General Engine

decking, engine

zero decking? height?

iroc.86 on 02-21-2008

02-23-2008 07:38 PM
by Orr89RocZ

Go to last post

7

498

Tech / General Engine

balance, balanced, block, blueprint, blueprinted, blueprinting, car, carburetor, crank, deck, decking, engine, height, mean, motor, squaring

Blueprinting, Balancing, What does it mean?

PedalToMetal on 08-23-2007

08-25-2007 05:16 AM
by ede

Go to last post

11

5,506

Tech / General Engine

305, 416, 601, chevy, deck, decking, diffrents, flat, heads, height, intake, milled, milling, pistons, top

milling/decking '416' heads

blyth18md on 12-18-2005

12-20-2005 12:11 AM
by Fast355

Go to last post

5

4,677

Tech / General Engine

decking, face, formula, intake, lower, machining, manifold, mill, sbc

Head machining

PaveTim on 01-13-2005

01-17-2005 07:50 PM
by anesthes

Go to last post

5

495

Tech / General Engine

alignment, block, decked, decking, manifold

Block decking, manifold alignment, etc

anesthes on 10-25-2004

10-25-2004 11:09 AM
by ede

Go to last post

1

441

Tech / General Engine

350, 3973487, 3973487x, 487x, casting, chevrolet, chevy, cylinder, decking, factory, good, gwads, head, heads, horsepower, sbc

head casting question

trans_am_racing on 10-15-2004

10-16-2004 11:31 PM
by THEGENERAL

Go to last post

6

5,485

Tech / General Engine

350, amount, block, car, decked, decking, head, heads, intake, mill, milled, milling, olds, proper, ratio, sbc, zeroed

zero decking block and milling intake

cormyr on 06-30-2004

06-30-2004 09:42 PM
by cormyr

Go to last post

4

1,102

Tech / General Engine

43l, block, compressor, decking, dummy, train, vortec

Compression Dummy

Randel '86 on 06-19-2004

06-20-2004 01:17 PM
by F-BIRD'88

Go to last post

6

594

Tech / General Engine

block, blocks, body, decking, sleeve, sleeved, sleeving

Decking block after re-sleeve?

erictheviking on 03-05-2004

03-06-2004 05:37 PM
by ede

Go to last post

5

903

Tech / General Engine

, alignment, block, car, dart, deck, decked, decking, head, heads, intake, iron, manifold, removed, surface

Block decking, and head alignment

spud on 12-05-2003

12-07-2003 10:44 AM
by spud

Go to last post

6

1,243

Tech / General Engine

average, avg, blick, block, cost, costs, decking, engine, honing, l98, maching, machingin, machining, price, prices, whats

What's an avg. price for block machining?

Raptor Pilot on 02-20-2002

02-20-2002 11:46 AM
by jichniow

Go to last post

3

2,094

Tech / General Engine

400, compression, decking, hight, piston, pistons, sbc, stock

Higher comp. on stock 400 pistons?

Hulk0202 on 11-19-2001

11-19-2001 03:10 PM
by Damon

Go to last post

7

643

Tech / General Engine

1mm, aluminum, chamber, combustion, cylinder, deck, decking, deep, head, marks, problems, scrape, scratch, scratched, scratches

Scratch in my Clyinder Head Deck (Is it fatal)

david auster on 04-22-2001

04-22-2001 04:11 PM
by david auster

Go to last post

2

1,006

Tech / General Engine

All times are GMT -5. The time now is 05:49 PM.