SGI-5C vs Speedometer for T56
06-16-2013, 09:49 AM
#1
SGI-5C vs Speedometer for T56
So this might just be the last glitch in my 383/T56 swap. I have the SGI-5C box hooked up to the ECM, tried all the various recommended Output 3 and 4 configurations = no speedo. The only Output the speedo moves at all on is Output 1, with switches all off. Speedo reads maybe triple actual speed (120 mph at 2000 rpm in 4th gear with 3.70 gears.)
According to the SGI-5 manual the only application for Output 1 is for a 64,000-250,000 ppm signal; a T56 is 25-40,000, correct? Something's not making sense here. Most of the searches turn up an answer that just doesn't quite apply to my combo.
Any suggestions?
According to the SGI-5 manual the only application for Output 1 is for a 64,000-250,000 ppm signal; a T56 is 25-40,000, correct? Something's not making sense here. Most of the searches turn up an answer that just doesn't quite apply to my combo.
Any suggestions?
06-19-2013, 01:41 PM
#4
Supreme Member
iTrader: (2)
Join Date: Jan 2001
Location: Tampa, FL, USA
Posts: 4,149
Likes: 0
Received 2 Likes
on
2 Posts
Car: 93 240SX
Engine: LQ9
Transmission: T56
Axle/Gears: 3.54 R200 IRS
Re: SGI-5C vs Speedometer for T56
Post up how you've got it wired, everything.
It sounds like its wired improperly.
It sounds like its wired improperly.
06-23-2013, 10:56 PM
#6
Re: SGI-5C vs Speedometer for T56
7730 ECM.
12v Power, Ground, Transmission VSS directly to Signal in and Signal Ground. As I said, OUT 1 is the only output that will generate movement on the speedo. All other OUTs read zero, no matter the switch settings. All 4 switches currently set to OFF.
Light on SGI flashes green when moving.
12v Power, Ground, Transmission VSS directly to Signal in and Signal Ground. As I said, OUT 1 is the only output that will generate movement on the speedo. All other OUTs read zero, no matter the switch settings. All 4 switches currently set to OFF.
Light on SGI flashes green when moving.
06-26-2013, 11:43 AM
#7
Supreme Member
iTrader: (2)
Join Date: Jan 2001
Location: Tampa, FL, USA
Posts: 4,149
Likes: 0
Received 2 Likes
on
2 Posts
Car: 93 240SX
Engine: LQ9
Transmission: T56
Axle/Gears: 3.54 R200 IRS
Re: SGI-5C vs Speedometer for T56
Switch 3 should be set to ON
You *should* be using out4, though its been about 8 years since I've last setup one of these with the same config you're doing.
Also i'd run a jumper wire over to the main ground from your signal ground connection.
You *should* be using out4, though its been about 8 years since I've last setup one of these with the same config you're doing.
Also i'd run a jumper wire over to the main ground from your signal ground connection.
Trending Topics
03-26-2015, 01:50 PM
#8
Re: SGI-5C vs Speedometer for T56
TTT. Regrounded as per suggestion. No other outputs will work. I've noticed that occasionally the speedo will drop to zero when driving and the car starts running HORRIBLY. After awhile it will shoot back up to its (incorrect by 250%) reading and run like butter.
Car is parked for another week or two, but thinking about this again for Spring. Do you think the speedo issue is the cause, or a symptom?
Should I buy and try another SGI-5?
Car is parked for another week or two, but thinking about this again for Spring. Do you think the speedo issue is the cause, or a symptom?
Should I buy and try another SGI-5?
03-26-2015, 01:51 PM
#9
Thread
Thread Starter
Forum
Replies
Last Post
