Third Generation F-Body Message Boards

 
Page 1 of 2
1
2
Search: Posts Made By: Chad91Rs
Showing results 1 to 50 of 73
Search took 0.42 seconds.
Forum: South Central Region
07-30-2002, 03:53 PM
Replies: 4
Views: 911
Posted By Chad91Rs

89Roc, I did pretty bad............ I didn't...

89Roc,
I did pretty bad............
I didn't call before I left and they were closed do to a stray shower that went through town.
I wasn't the only one going WTF though so...

I'll be up there...
Forum: South Central Region
07-23-2002, 11:25 PM
Replies: 4
Views: 911
Posted By Chad91Rs

New Track! - Redline Raceway, Royce City, NE of Dallas

Like the title says there's a new 1/8 mile track out in Royce City.
It's at exit 83 off of I30. Can't miss it.
I was out last Friday night for the 1st time and the place is damn nice, alot better...
Forum: Suspension and Chassis
02-19-2002, 05:31 PM
Replies: 3
Views: 836
Posted By Chad91Rs

The 17x11" rims will fit with 315's. You'll...

The 17x11" rims will fit with 315's.
You'll need 6" of backspacing for them to clear.
I also don't recommend them if the car is lowered.
On hard bumps they will rub on the upper wheel well.
Forum: Suspension and Chassis
02-19-2002, 05:27 PM
Replies: 1
Views: 3,582
Posted By Chad91Rs

I have 17x11's in the rear with 315/35/17's. If...

I have 17x11's in the rear with 315/35/17's.
If you wanna go with the ten inch rim 5.5 inches of backspacing is what you need.
Forum: Suspension and Chassis
01-04-2002, 11:27 PM
Replies: 2
Views: 986
Posted By Chad91Rs

Mark, I can tell you a few things. With 6"...

Mark,
I can tell you a few things.
With 6" of backspacing the 17x11's will fit with a little hammer to the inner wheel well in back.
Then you only have to worry about hard dips in the road...
Forum: TBI
12-07-2001, 06:52 PM
Replies: 4
Views: 3,200
Posted By Chad91Rs

JPrevost, Thanks for the help. Can't wait to...

JPrevost,
Thanks for the help.
Can't wait to get the damn thing back on the road.
Forum: TBI
12-06-2001, 09:57 PM
Replies: 4
Views: 3,200
Posted By Chad91Rs

Trans/ throttle bracket problem!

Here is my problem.
I've just installed new heads, cam, and a Vortec Air Gap manifold.
The stock bracket does not fit.
I then get the holley bracket for a aftermarket manifold and it doesn't line...
Forum: Suspension and Chassis
11-20-2001, 11:02 PM
Replies: 2
Views: 421
Posted By Chad91Rs

You could go with a 295/50/16. It's your best...

You could go with a 295/50/16.
It's your best bet at that height.
It stands 27.6" tall.
The backspacing would have to be perfect to fit in inside the wheel well though.
Forum: Suspension and Chassis
11-18-2001, 07:47 PM
Replies: 5
Views: 3,248
Posted By Chad91Rs

You'll need 6" of backspacing on a 17x11" rim to...

You'll need 6" of backspacing on a 17x11" rim to fit.
This is a concrete #.
I've had mine on for 2 years or so.
You will get some rubbing on the top, tip wheel well lip on hard dips since the tire...
Forum: Suspension and Chassis
11-08-2001, 12:25 PM
Replies: 14
Views: 794
Posted By Chad91Rs

Some answers to your questions. 1)91 RS Camaro ...

Some answers to your questions.
1)91 RS Camaro
2)The only rubbing is on hard dips in the road against the outer wheel well lip since the tire does stick out past the wheel well
3)backspacing is 6"...
Forum: Suspension and Chassis
11-05-2001, 11:46 PM
Replies: 14
Views: 794
Posted By Chad91Rs

Lower control arms Lowering brackets Posi ...

Lower control arms
Lowering brackets
Posi
17x11" rims with 315/35/17"s in the rear

This combination works very well for me.
Forum: Tech / General Engine
11-05-2001, 11:34 PM
Replies: 3
Views: 312
Posted By Chad91Rs

Headers.....you won't believe the difference. ...

Headers.....you won't believe the difference.
The manifold by itself won't do you much good.
Headers 1st, then a cam & manifold swap at the same time is my suggestion.
Forum: Aftermarket Product Review
11-05-2001, 11:23 PM
Replies: 28
Views: 11,916
Posted By Chad91Rs

LT1 cam = 201/208 duration, 447/459 lift

LT1 cam = 201/208 duration, 447/459 lift
Forum: TBI
10-29-2001, 09:06 PM
Replies: 9
Views: 456
Posted By Chad91Rs

Understeer is not a problem for me with my setup....

Understeer is not a problem for me with my setup.
17x11" in back with 315/35/17 and 17x8" with 235/45/17 in the front.

Like Andy I have ALL things unimportant gone (carpet, stereo, seats,...
Forum: Tech / General Engine
10-29-2001, 08:48 PM
Replies: 11
Views: 5,048
Posted By Chad91Rs

Thanks for your help guys. SpankuGta, I...

Thanks for your help guys.

SpankuGta, I might get back with you about the LT1 cam.
Forum: Tech / General Engine
10-28-2001, 06:51 PM
Replies: 11
Views: 5,048
Posted By Chad91Rs

? about LT4 cam + 1.5 rockers

I'm looking to install the stock LT4 cam(203/210 duration, 476/480 lift w/1.6 rockers) into a 305 TBI with vortec heads.

I was told by a rep at a speed shop that the stock LT4 cam can't be used...
Forum: TBI
10-23-2001, 02:01 PM
Replies: 9
Views: 352
Posted By Chad91Rs

dmair, I agree with what you've said and I...

dmair,
I agree with what you've said and I don't mind lossing some torque for some more mid or upper rpm power.

My car redlines in 1st at about 10mph with my set up which includes 3:73 gears and...
Forum: TBI
10-23-2001, 12:13 AM
Replies: 9
Views: 352
Posted By Chad91Rs

I got the ZZ3 cam a year or two back when they...

I got the ZZ3 cam a year or two back when they were being sold for dirt cheap as takeouts.

Thats why it's in the equation.
I need to know if the computer is gonna say "I don't think so" when it's...
Forum: TBI
10-22-2001, 11:57 PM
Replies: 9
Views: 352
Posted By Chad91Rs

I've got my GMPP catalog here in front of me and...

I've got my GMPP catalog here in front of me and it says the ZZ3 and ZZ4 cam are the same.

I was afraid the 221 duration might be a little too much for the computer myself.
Forum: TBI
10-22-2001, 11:09 PM
Replies: 9
Views: 352
Posted By Chad91Rs

Opinions on this combo PLEASE...

Any educated criticism (or fact unknown to me) will be appreciated.

305 TBI with:
1) ZZ3 cam 208/221 duration 474/510 lift
2) Vortec heads made capable of .600 lift and milled slightly
3)...
Forum: Aftermarket Product Review
02-08-2001, 05:14 PM
Replies: 9
Views: 2,726
Posted By Chad91Rs

315/35/17's will fit. Myself and a few others...

315/35/17's will fit.
Myself and a few others have them.
You need 6" of offset for them to clear the inner most contact point after you hammer them out a bit.
If you stay with either a 15" or 16"...
Forum: Suspension and Chassis
02-05-2001, 11:26 PM
Replies: 22
Views: 697
Posted By Chad91Rs

Macgyver, thanks for the complament. I own 13...

Macgyver, thanks for the complament.
I own 13 guitars currently and alot of other equipment not pictured.
I've since bought another San Dimas USA Jackson but my bad boys are the ESP Kamakazi and my...
Forum: Suspension and Chassis
02-05-2001, 06:23 PM
Replies: 22
Views: 697
Posted By Chad91Rs

Here are some pics of my car with 17x11's in the...

Here are some pics of my car with 17x11's in the rear, with 315/35/17's.
These pics are a year or older with the stock rims in front.
I now have 17x8's with 235/45/17's.
They give the car a mean...
Forum: Organized Drag Racing and Autocross
12-12-2000, 08:42 AM
Replies: 7
Views: 405
Posted By Chad91Rs

Kick *** times Mark.

Kick *** times Mark.
Forum: Suspension and Chassis
11-24-2000, 08:52 PM
Replies: 3
Views: 425
Posted By Chad91Rs

I think Suspension Techniques makes a larger than...

I think Suspension Techniques makes a larger than 36mm bar for the front.
If I remember right, it's been a while.
Forum: Suspension and Chassis
11-20-2000, 11:05 PM
Replies: 1
Views: 327
Posted By Chad91Rs

They make sizes of 265/275/285 and 295 for a 16"...

They make sizes of 265/275/285 and 295 for a 16" rim.
The problem is no one stocks them.
I have run into the same problem.
You'll need to have a local shop order them or go to tirerack.com .
Best...
Forum: TBI
11-02-2000, 04:27 PM
Replies: 50
Views: 1,477
Posted By Chad91Rs

I asked one guy here a while back and he said he...

I asked one guy here a while back and he said he gained over a full second on a 120 horse shot.
Like 1.1 seconds I think.
That thing better be tuned to the max first though.

[This message has...
Forum: Organized Drag Racing and Autocross
11-01-2000, 09:36 PM
Replies: 3
Views: 622
Posted By Chad91Rs

You can fit a 17x11" rim with 6" backspacing in...

You can fit a 17x11" rim with 6" backspacing in the rear and a 9.5" rim with 5" backspacing in front.
315/35/17's in back and 275/40/17's in the front.

You might be able to fit a 285 up front...
Forum: Organized Drag Racing and Autocross
10-31-2000, 08:37 PM
Replies: 4
Views: 487
Posted By Chad91Rs

The problem isn't a wide rim, but the limited...

The problem isn't a wide rim, but the limited choice in 16" tires.
The largest I know of is 295/50 and that would only work for the rear.
There are several makers of 16x9.5" rims out there like...
Forum: Engine Swap
10-18-2000, 07:31 PM
Replies: 16
Views: 1,478
Posted By Chad91Rs

I'm seriously considering this swap also. ...

I'm seriously considering this swap also.

Jim Pace has the Ram Jet for $4199.
Forum: Organized Drag Racing and Autocross
10-18-2000, 05:44 PM
Replies: 5
Views: 378
Posted By Chad91Rs

I'd go with some LCA($90), posi($310), and some...

I'd go with some LCA($90), posi($310), and some 3.42 gears ($150).
If you have a ZZ4 these should be mandatory, I repeat mandatory.
I guess it might cost you more overseas.
Also, some LCA lowering...
Forum: Engine Swap
10-16-2000, 06:33 PM
Replies: 3
Views: 767
Posted By Chad91Rs

Try www.speedomotive.com...

Try www.speedomotive.com (http://www.speedomotive.com)
Forum: Suspension and Chassis
10-16-2000, 10:51 AM
Replies: 5
Views: 431
Posted By Chad91Rs

Herb Adams (Moroso) makes the largest one I could...

Herb Adams (Moroso) makes the largest one I could find at 1.125".
It really stiffened the rear to the tenth degree.
Forum: Tech / General Engine
10-15-2000, 07:10 PM
Replies: 7
Views: 380
Posted By Chad91Rs

Those cars made 210 hp (positive) and around 400...

Those cars made 210 hp (positive) and around 400 tq.
I know this cause a friend has one.
I found an old Chilton with all the power figures and thats what it had for torque.

With that...
Forum: Suspension and Chassis
10-15-2000, 11:52 AM
Replies: 3
Views: 420
Posted By Chad91Rs

All you need are some LCA's and LCA brakets. ...

All you need are some LCA's and LCA brakets.
With these you'll say goodbye to your problem.
Forum: Wheels and Tires
10-09-2000, 08:06 PM
Replies: 9
Views: 921
Posted By Chad91Rs

Jarod, those rims rock. Yes, you can fit a...

Jarod, those rims rock.

Yes, you can fit a 17x11" rim on the back of a 3rd gen.
You need 6" of backspacing.
They will stick out past the wheel well a little.
This tire rim combo helps in...
Forum: Suspension and Chassis
10-07-2000, 10:06 PM
Replies: 5
Views: 431
Posted By Chad91Rs

I've owned 3- 3rdgens, 86'/91'/91', and none of...

I've owned 3- 3rdgens, 86'/91'/91', and none of them rub in the front at all except when I installed a taller tire.
Forum: Suspension and Chassis
10-07-2000, 07:35 PM
Replies: 5
Views: 431
Posted By Chad91Rs

Sounds to me like you might have taller than...

Sounds to me like you might have taller than stock tires installed.

What size are your rims and what size tires do you have on them?
Unless you have some kind of front end damage it would have...
Forum: Suspension and Chassis
10-07-2000, 01:55 PM
Replies: 4
Views: 468
Posted By Chad91Rs

Yeah they'll work. I'd go with a 235/45/17...

Yeah they'll work.

I'd go with a 235/45/17 or 245/45/17 on an 8" rim.
Forum: Suspension and Chassis
10-07-2000, 01:47 PM
Replies: 2
Views: 750
Posted By Chad91Rs

Not all tires are created equal. I've noticed...

Not all tires are created equal.
I've noticed the same differences you mentioned above as well.
This is a problem you'll find when you mix brands.
My advise is get some sticky tires, like some...
Forum: Suspension and Chassis
10-06-2000, 06:53 PM
Replies: 4
Views: 943
Posted By Chad91Rs

Yeah, that size will fit. You could go as large...

Yeah, that size will fit.
You could go as large as 26x10.5x15 on a 7" rim.
I'd go with a 26x9.5x15.
That should be more than enough for most of us third gen guys.
Forum: Suspension and Chassis
10-04-2000, 06:22 PM
Replies: 2
Views: 371
Posted By Chad91Rs

Depends on your goals as far as sizes go. If...

Depends on your goals as far as sizes go.

If you're going for traction and that large tire look in the back you could go with either 295/50/16, 275/50/16, or 265/50/16.
Like Justin said the...
Forum: TBI
10-03-2000, 05:45 PM
Replies: 9
Views: 2,951
Posted By Chad91Rs

This sounds like a better alternative than...

This sounds like a better alternative than hunting down a 454 unit and the hassles of the electrical connections being different.

I'd be very interested in someones results.
Forum: Organized Drag Racing and Autocross
09-28-2000, 09:04 PM
Replies: 4
Views: 531
Posted By Chad91Rs

I can't say for sure but my best guess is around...

I can't say for sure but my best guess is around 1/2" at the most.

I think they'll tuck under completely though.
Forum: Suspension and Chassis
09-28-2000, 06:09 PM
Replies: 1
Views: 365
Posted By Chad91Rs

A 295/50/15 is about the biggest street tire you...

A 295/50/15 is about the biggest street tire you can get without going with more of a "strip tire".
I suggest you check out some at Tirerack.com

They have seveal 295/50/15's for under $100.
The...
Forum: Tech / General Engine
09-28-2000, 05:50 PM
Replies: 2
Views: 443
Posted By Chad91Rs

I think the different offsets were only on the...

I think the different offsets were only on the factory 16" rims.
The stock 15x7's were the same offset if I'm not mistaken.
Forum: Organized Drag Racing and Autocross
09-28-2000, 05:47 PM
Replies: 4
Views: 531
Posted By Chad91Rs

I'm running 17x11's on my rearend with...

I'm running 17x11's on my rearend with 315/35/17's and 6" offset.
I had to do a little masaging with a hammer
but it fit.
If you're drag racing I'd go with a 15x10" rim with 5.5" backspacing and...
Forum: Organized Drag Racing and Autocross
09-27-2000, 06:49 PM
Replies: 10
Views: 765
Posted By Chad91Rs

I just read this. The McCreary tires are only...

I just read this.
The McCreary tires are only legal "WITH" inner tubes.
They ran them without.
If you're only running on say the weekends at the strip I'd say forget them.
Just check your...
Forum: Organized Drag Racing and Autocross
09-27-2000, 06:41 PM
Replies: 10
Views: 765
Posted By Chad91Rs

Yes, they are street legal. They have a...

Yes, they are street legal.

They have a tread pattern similar to the M/T Spotsmans or the Hoosier Quick Time tires.
You can find these in a Summit/Jegs catalog.
Forum: Organized Drag Racing and Autocross
09-27-2000, 06:28 PM
Replies: 10
Views: 765
Posted By Chad91Rs

Found it. They tested a 275/50/15 on a 10" rim....

Found it. They tested a 275/50/15 on a 10" rim. It looks great. On your 7" it'll look deformed.

The other tire is a McCleary Road Star.
It tested a hair "better" than the BFG drag radials. It...
Showing results 1 to 50 of 73
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -5. The time now is 04:27 AM.