Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: Dan87IROC-Z
Showing results 1 to 50 of 500
Search took 1.00 seconds.
Forum: Tech / General Engine
02-20-2002, 12:03 AM
Replies: 11
Views: 12,591
Posted By Dan87IROC-Z

I wouldn't go with anything larger than the 1.84"...

I wouldn't go with anything larger than the 1.84" intake valves. Yes, the 1.94"s will fit and maybe the 2.02"s, but you will have some pretty serious shrouding problems. Bigger valves isn't always...
Forum: Tech / General Engine
12-29-2001, 06:38 PM
Replies: 12
Views: 1,114
Posted By Dan87IROC-Z

I take my 350 to 6000 on a regular basis. I do...

I take my 350 to 6000 on a regular basis. I do however have a pretty tricked out engine with new valve springs.
Forum: Tech / General Engine
12-29-2001, 06:28 PM
Replies: 33
Views: 1,387
Posted By Dan87IROC-Z

You are going to have to replace that crappy T-5...

You are going to have to replace that crappy T-5 anyway, so, if having a manual transmission is that important to you, then convert you 350/auto to an 5 or 6 speed. The Richmond 6 speed is the best...
Forum: Tech / General Engine
12-29-2001, 06:22 PM
Replies: 2
Views: 643
Posted By Dan87IROC-Z

Best way(s) to loose weight?

Whats the best way to get rid of un-wanted weight from our cars? I don't want to be pulling out seats or anything like that. I already took out the spare tire and jack, but what else can I do?
Forum: Aftermarket Product Review
11-08-2001, 08:56 PM
Replies: 28
Views: 1,150
Posted By Dan87IROC-Z

I think that the TFs are only out-flowed by the...

I think that the TFs are only out-flowed by the AFRs, assuming that the chambers and ports are all the same sizes, so go with either the Trick Flows or the AFRs. I wouldn't go with GM heads if you...
Forum: Aftermarket Product Review
11-08-2001, 08:52 PM
Replies: 37
Views: 1,164
Posted By Dan87IROC-Z

Well it really all depends on what you want. ...

Well it really all depends on what you want. There is no "best" setup. When I am done with the 350 in my car, I will have the LT4 HOT cam, Accel intake base, SLP runners, ported plenum and Trick...
Forum: Aftermarket Product Review
11-08-2001, 08:44 PM
Replies: 30
Views: 1,469
Posted By Dan87IROC-Z

Unshrouding the valves means moving them farther...

Unshrouding the valves means moving them farther away from the sides of the chambers and farther from eachother so that the air/fuel mixture has more room to move into the cylinder and can keep...
Forum: TPI
10-31-2001, 04:50 PM
Replies: 20
Views: 3,471
Posted By Dan87IROC-Z

I agree with Matt, the LT4 HOT Cam would be an...

I agree with Matt, the LT4 HOT Cam would be an ideal choice for your car. I'm going to get a set of SLP runners and some Trick Flow heads and it all should work great with that setup which is very...
Forum: Exhaust
10-31-2001, 04:43 PM
Replies: 6
Views: 565
Posted By Dan87IROC-Z

When I installed my TES headers (1 5/8") my ETs...

When I installed my TES headers (1 5/8") my ETs dropped by .3, and that was on a stock motor. I bet you can see at least that since you are installing larger ones, but you will loose some power...
Forum: Tech / General Engine
10-29-2001, 02:30 PM
Replies: 11
Views: 5,048
Posted By Dan87IROC-Z

The LT4 HOT Cam has .525" lift with the 1.6...

The LT4 HOT Cam has .525" lift with the 1.6 rockers. If you use the stock 1.5s, its only .492", or .498" if you have 1.52s like I do. I agree with what Kevin said, the only restriction you have...
Forum: Tech / General Engine
10-27-2001, 11:15 PM
Replies: 22
Views: 457
Posted By Dan87IROC-Z

I like the looks of the Camaros better than the...

I like the looks of the Camaros better than the Firebirds, and I like the IROCs best of the Camaros!

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg...
Forum: TPI
10-27-2001, 11:11 PM
Replies: 10
Views: 556
Posted By Dan87IROC-Z

Also remember you're going to need the MR chip,...

Also remember you're going to need the MR chip, which is another $550 I think.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9 Bolt...
Forum: TPI
10-27-2001, 11:09 PM
Replies: 10
Views: 362
Posted By Dan87IROC-Z

You'll need a short runner intake to go over...

You'll need a short runner intake to go over 6500. And I would also suggest going with something other than a 383 if you want to rev to 7000+.

------------------
1987 Chevy Camaro IROC-Z
L98...
Forum: Exhaust
10-27-2001, 11:04 PM
Replies: 3
Views: 405
Posted By Dan87IROC-Z

I would suggest the Hooker cat-back from Jegs. ...

I would suggest the Hooker cat-back from Jegs. You can't go wrong, its a great system!

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75"...
Forum: Exhaust
10-27-2001, 11:03 PM
Replies: 18
Views: 625
Posted By Dan87IROC-Z

I don't think I could be happier with the Hooker...

I don't think I could be happier with the Hooker system I got. I do know that I like it a lot better than any Flowmaster system, but I don't know too much about the SLP.

------------------
1987...
Forum: Aftermarket Product Review
10-27-2001, 11:00 PM
Replies: 3
Views: 412
Posted By Dan87IROC-Z

Yeah, anywhere, autozone, napa, checker,...

Yeah, anywhere, autozone, napa, checker, anywhere!

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9 Bolt Rear End with 2.77:1 Gears.
...
Forum: Aftermarket Product Review
10-23-2001, 08:55 PM
Replies: 18
Views: 2,065
Posted By Dan87IROC-Z

I think they would work great, as long as you...

I think they would work great, as long as you match the cam with it correctly. The LT4 HOT Cam would be way to big for that motor. Look for something with a .050 duration around 210 and lift of...
Forum: Tech / General Engine
10-22-2001, 07:12 PM
Replies: 13
Views: 602
Posted By Dan87IROC-Z

Yeah, I already have pulled out some un-necessary...

Yeah, I already have pulled out some un-necessary stuff from my car. Like the all the AC crap and the windshield washer fluid tank. I really don't want to strip the car down, I like having some...
Forum: Tech / General Engine
10-19-2001, 10:44 PM
Replies: 13
Views: 602
Posted By Dan87IROC-Z

Altight, thanks guys. Where do I buy a DFI and...

Altight, thanks guys. Where do I buy a DFI and what does it cost? Also, what are some things I can do to lower the weight? I do plan on having my 377 be an aluminum long block.
...
Forum: Tech / General Engine
10-19-2001, 10:38 PM
Replies: 19
Views: 423
Posted By Dan87IROC-Z

I agree with Mark, go with A or B, those are your...

I agree with Mark, go with A or B, those are your best bet! Just a suggestion, you could consider getting a set of Trick Flow heads, they are a little less than a $1000, maybe enough would be left...
Forum: TPI
10-19-2001, 10:34 PM
Replies: 2
Views: 570
Posted By Dan87IROC-Z

Port Matching Questions for TPI parts.

I have the LPE SuperRam base, not ported or anything, just straight out of the box. I would like to get a set of the SLP runners from Summit. My question is, will I have to port match (or...
Forum: Exhaust
10-19-2001, 10:28 PM
Replies: 3
Views: 386
Posted By Dan87IROC-Z

Yes, get a 3 way 3" in/3" out from Catco, it will...

Yes, get a 3 way 3" in/3" out from Catco, it will cost you about $110 from Summit.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9...
Forum: Aftermarket Product Review
10-19-2001, 10:25 PM
Replies: 4
Views: 454
Posted By Dan87IROC-Z

My Edelbrock TES headers are almost 2 years old...

My Edelbrock TES headers are almost 2 years old and are un-coated, and are only rusting (very minimally I might add) on one small part of the header. It is costly to have them coated, and it is...
Forum: Tech / General Engine
10-18-2001, 06:32 PM
Replies: 13
Views: 602
Posted By Dan87IROC-Z

What do you mean make sure its not a fat elvis? ...

What do you mean make sure its not a fat elvis?

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9 Bolt Rear End with 2.77:1 Gears.
...
Forum: Exhaust
10-17-2001, 06:02 PM
Replies: 24
Views: 1,472
Posted By Dan87IROC-Z

I love hte way mine sounds. Its definetly better...

I love hte way mine sounds. Its definetly better sounding than the Flowmaster systems. Its a deep, powerful sound, but not really raspy like the Flowmasters.

------------------
1987 Chevy...
Forum: Tech / General Engine
10-17-2001, 05:58 PM
Replies: 13
Views: 7,734
Posted By Dan87IROC-Z

I would suggest the Accel 300+ race wires. They...

I would suggest the Accel 300+ race wires. They are the best set of wires I've ever had, they are 8.8mm and cost around $60 from Jegs.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350...
Forum: Tech / General Engine
10-17-2001, 05:55 PM
Replies: 5
Views: 416
Posted By Dan87IROC-Z

You want to be at your peak power RPM in your 1:1...

You want to be at your peak power RPM in your 1:1 gear (3rd). Like for my car, I'd want to be at about 5000 RPM in 3rd going through the traps. Go to the equations part of this site and figure out...
Forum: Tech / General Engine
10-17-2001, 05:52 PM
Replies: 13
Views: 602
Posted By Dan87IROC-Z

Possible to make power to 7000RPM with fuel injection?

And I mean real fuel injection, not some TBI knock off. I was thinking of building a 377 fed with a Mini Ram, big cam, AFR 195s, big exhaust and such. Would it be possible, with porting the MR to...
Forum: Tech / General Engine
10-16-2001, 07:52 PM
Replies: 18
Views: 624
Posted By Dan87IROC-Z

What about on IROC rims, whats the biggest that...

What about on IROC rims, whats the biggest that can go on there and still be effective? Can I use 255s or 265s? Also, could I get a smaller diameter, like 40 or 35s even?

------------------...
Forum: Tech / General Engine
10-09-2001, 11:05 PM
Replies: 15
Views: 431
Posted By Dan87IROC-Z

I use Mobil 1 10W30 synthetic and an AC Delco...

I use Mobil 1 10W30 synthetic and an AC Delco filter, I buy both from Wal-Mart.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9 Bolt...
Forum: TPI
10-06-2001, 09:18 PM
Replies: 8
Views: 3,814
Posted By Dan87IROC-Z

Its a great cam, you'll really like it. I just...

Its a great cam, you'll really like it. I just used a small tack hammer to tap the dowel pin back in. I got mine for $165 from www.gmpartsdirect.com! (http://www.gmpartsdirect.com!)
...
Forum: TPI
10-06-2001, 09:15 PM
Replies: 42
Views: 1,831
Posted By Dan87IROC-Z

In reasponce to what 89IROCZZ4 said: ...

In reasponce to what 89IROCZZ4 said:

Wouldn't it be ideal to have the best of both worlds? Is that even possible. I'm talkin a car that runs mid to low 11s and can still kick anyones *** on the...
Forum: Tech / General Engine
10-06-2001, 09:01 PM
Replies: 8
Views: 676
Posted By Dan87IROC-Z

My car does the same thing as yours does. I've...

My car does the same thing as yours does. I've been told that SBCs have GREAT oiling systems and you only need 10psi per every 1000 RPM. I use Mobil 1 10W30 by the way.

------------------
1987...
Forum: Tech / General Engine
10-06-2001, 08:58 PM
Replies: 6
Views: 336
Posted By Dan87IROC-Z

I would for sure go with the intake. As long as...

I would for sure go with the intake. As long as all your ignition system components are in good shape, you shouldn't need a better coil with the set-up you have now. The reason the car only pulls...
Forum: Tech / General Engine
10-06-2001, 08:55 PM
Replies: 6
Views: 398
Posted By Dan87IROC-Z

400s come with a 2 piece rear main seal, so I...

400s come with a 2 piece rear main seal, so I think you will need to change the bellhousing on your tranney too, but I'm not sure. I do know that you can buy a 2 piece to 1 piece adapter for it, its...
Forum: Tech / General Engine
10-05-2001, 03:28 PM
Replies: 1
Views: 362
Posted By Dan87IROC-Z

Where can I correct my ET for elevation?

The site I used to use doesn't work any longer, so does anyone know of any?

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner 7.75" 9 Bolt Rear...
Forum: Tech / General Engine
10-05-2001, 03:25 PM
Replies: 10
Views: 2,846
Posted By Dan87IROC-Z

How does the gap of the plugs affect the car's...

How does the gap of the plugs affect the car's performance. I have a 300+ wires and then AC cap, rotor and rapid fires gapped at .035, what would changing that gap to .045+ do?

------------------...
Forum: Tech / General Engine
10-05-2001, 03:20 PM
Replies: 11
Views: 2,551
Posted By Dan87IROC-Z

I think its okay to go with an LSA for 110*. ...

I think its okay to go with an LSA for 110*. Almost all of the cams that Comp Cams sells have an LSA of 110*, I was planning on using one of them in my 377.

------------------
1987 Chevy Camaro...
Forum: Tech / General Engine
10-05-2001, 03:09 PM
Replies: 7
Views: 440
Posted By Dan87IROC-Z

No, you don't have to modify your chip when doing...

No, you don't have to modify your chip when doing a thermostat change. Acctually, most aftermarket chips require a lower temperature stat because it increases your timing and can lead to detonation...
Forum: Tech / General Engine
10-05-2001, 03:04 PM
Replies: 3
Views: 500
Posted By Dan87IROC-Z

Thats right, no lube requiered for hydraulic...

Thats right, no lube requiered for hydraulic roller cams. I just coverd the lobes and such with some oil and slid it right in!

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH...
Forum: Tech / General Engine
10-04-2001, 11:31 PM
Replies: 7
Views: 622
Posted By Dan87IROC-Z

Thanks for the advice guys. I know a 400 would...

Thanks for the advice guys. I know a 400 would probably be better, but I want a 377. I have already decided that, its pretty unique and there's other reasons too. But thanks again guys!
...
Forum: Tech / General Engine
10-01-2001, 06:14 PM
Replies: 7
Views: 622
Posted By Dan87IROC-Z

Anyone who's built a 377, step in...lots of ?s

I am planning on building a 377 (400 block, 350 crank) next summer for my car. I want the 377 so I can have a high revving engine, capable of pushing 7500 RPM and making 450+ hp.

Where did you...
Forum: Exhaust
09-30-2001, 11:02 PM
Replies: 19
Views: 750
Posted By Dan87IROC-Z

You're wrong Kevin. I have been 100% happy with...

You're wrong Kevin. I have been 100% happy with my Edelbrock headers, I've had them for almost 2 years now, and I have a friend who has had them for almost 3 years. Neither of ours are coated, and...
Forum: TPI
09-29-2001, 09:47 PM
Replies: 12
Views: 408
Posted By Dan87IROC-Z

Yeah, that is a GREAT deal. You know what you...

Yeah, that is a GREAT deal. You know what you would pay for that brand new? With that kind of a deal, I would take it to a professional shop and have it all fully ported and maybe even get a new...
Forum: TPI
09-28-2001, 03:56 PM
Replies: 5
Views: 667
Posted By Dan87IROC-Z

I think the L98 angle plugs are for the...

I think the L98 angle plugs are for the Corvettes, just get the 64cc chamber straight plug heads.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg...
Forum: TPI
09-28-2001, 03:48 PM
Replies: 8
Views: 1,206
Posted By Dan87IROC-Z

Since your using just a 350, I would go with the...

Since your using just a 350, I would go with the AFR 190s, not 195s. The 195s would probably shift the power band too high for the displacement you have. You could also look at the 180s and just...
Forum: Exhaust
09-28-2001, 03:40 PM
Replies: 2
Views: 560
Posted By Dan87IROC-Z

I think thats the one I got, and its a full 3"...

I think thats the one I got, and its a full 3" system, but call the guys at Jegs to be sure.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4 Transmission
Borg Warner...
Forum: Exhaust
09-28-2001, 03:35 PM
Replies: 5
Views: 367
Posted By Dan87IROC-Z

I would get the HO one from Jegs, thats the one I...

I would get the HO one from Jegs, thats the one I got. Its full 3" with an Aerochamber muffler and quad 3" chrom tips.

------------------
1987 Chevy Camaro IROC-Z
L98 TPI 350 (5.7L)
TH 700R-4...
Forum: Exhaust
09-28-2001, 03:32 PM
Replies: 7
Views: 494
Posted By Dan87IROC-Z

I would recomend it! I installed a Catco one...

I would recomend it! I installed a Catco one that I got from Summit for $110, it made a nice difference and made the car a louder with a deeper tone!

------------------
1987 Chevy Camaro IROC-Z...
Forum: Aftermarket Product Review
09-22-2001, 08:01 PM
Replies: 7
Views: 427
Posted By Dan87IROC-Z

Yeah, I thought the base seated nicely on the...

Yeah, I thought the base seated nicely on the block and heads, but my stock runners were a PITA to install, I accidently cross threaded one of the bolts, and the PCV port on the base didn't fit right...
Showing results 1 to 50 of 500
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 01:02 PM.