Third Generation F-Body Message Boards

 
Page 1 of 5
1
2
3
4
5
Search: Posts Made By: jpk91rs
Showing results 1 to 50 of 238
Search took 0.23 seconds.
Forum: DIY PROM
06-22-2015, 03:18 PM
Replies: 30
Views: 4,406
Posted By jpk91rs

Re: New to DIY Prom.... EBL or Ostrich?

You can also buy a premade MAP plug from most parts stores for cheap. I ordered the MAP and plug with 6" harness from O'Reilly Auto Parts for $63.00 total. All new stuff.
Forum: Exhaust
12-18-2012, 08:12 PM
Replies: 10
Views: 5,790
Posted By jpk91rs

Re: Exhaust Leak...cracked manifold?

I found that my drivers side exhaust manifold had 2 broken bolts. It was the rear two and it was hard to see.
Forum: Car Audio
10-04-2011, 10:38 AM
Replies: 27
Views: 5,769
Posted By jpk91rs

Re: Sounds best in Third gen...Sealed or Ported?

I bought a Super Bass Box ported box with a Solobaric L7 10" speaker with dual 2 ohm voice coils, hooked it up to a Memphis Bell 16-MCH-1300 and I cannot sit in the car when it is turned up. The...
Forum: Miscellaneous Third Gen Items!
10-03-2011, 07:13 AM
Replies: 26
Views: 2,921
Posted By jpk91rs

Re: 1986 Camaro Shop Manual

I will take a copy. I just picked up a 1986 IROC-Z.
Forum: Engine/Drivetrain/Suspension Parts for Sale
09-29-2011, 02:25 PM
Replies: 6
Views: 623
Posted By jpk91rs

Re: TPI intake ducting

$50.00 it is then. Send me your info on how you want to be paid in a PM and I will get you paid.

Thanks.
JPK:thanks:
Forum: Engine/Drivetrain/Suspension Parts for Sale
09-28-2011, 08:18 PM
Replies: 6
Views: 623
Posted By jpk91rs

Re: TPI intake ducting

I will give you $35.00 plus shipping for it.
Forum: TPI
03-15-2007, 08:41 PM
Replies: 23
Views: 3,360
Posted By jpk91rs

I call BS on the vortec heads not flowing well....

I call BS on the vortec heads not flowing well. :bs: :crazy:
My old hot Stock dirt car ran an ultra light 355 with a nasty solid cam, vortec heads angle milled with 2.02 intake and 1.60 exhaust...
Forum: TPI
01-07-2007, 05:25 PM
Replies: 1
Views: 436
Posted By jpk91rs

Go to Sears and buy the rounded off bolt...

Go to Sears and buy the rounded off bolt extractor set. I have used it to remove a rounded off tranny drain plug and a broken off exhaust manifold bolt.
Forum: Car Audio
12-30-2006, 07:47 AM
Replies: 3
Views: 643
Posted By jpk91rs

Memphis 4 x 6 speakers, with the directional...

Memphis 4 x 6 speakers, with the directional tweeter will fit also.
Forum: Carburetors
12-10-2006, 10:51 AM
Replies: 23
Views: 8,494
Posted By jpk91rs

There is no need to hack or cut anything when...

There is no need to hack or cut anything when doing a fuel pump replacement. If you remove the panhard bar and remove the shocks and the sway bar from the rearend it will drop completely out of the...
Forum: Car Audio
12-10-2006, 10:32 AM
Replies: 32
Views: 1,388
Posted By jpk91rs

1 ea, 10" L7 Solobaric with 1100 RMS in a ported...

1 ea, 10" L7 Solobaric with 1100 RMS in a ported box and lots of Dynamat. No glass breakage of any kind. Will make your ears ring, though.:nod:
Forum: Car Audio
12-10-2006, 10:29 AM
Replies: 16
Views: 676
Posted By jpk91rs

My opinion is to put poly fill in the box. :nod: ...

My opinion is to put poly fill in the box. :nod: I can tell the difference in the sound.
Forum: Exhaust
11-26-2006, 05:39 AM
Replies: 5
Views: 631
Posted By jpk91rs

I bought the Hooker cat back system for my 91 RS....

I bought the Hooker cat back system for my 91 RS. I love the sound. Deep rumble inside and outside the car.
Forum: Car Audio
11-26-2006, 05:30 AM
Replies: 16
Views: 1,174
Posted By jpk91rs

I run a single 10" L7 Solobaric. It is a ported...

I run a single 10" L7 Solobaric. It is a ported box with 1100 RMS being fed to it and you cannot sit in the car. The amp I use is a Memphis Belle 5 channel amp. I love this amp so much. 75 watts RMS...
Forum: Car Audio
11-26-2006, 05:19 AM
Replies: 11
Views: 1,127
Posted By jpk91rs

Dynomat will stop all rattles. I have 2 1/2 bulk...

Dynomat will stop all rattles. I have 2 1/2 bulk kits in my 91 RS and it has very few rattles.
Forum: Car Audio
11-25-2006, 06:22 PM
Replies: 192
Important/Useful : Dimensions for well sub box
Views: 166,438
Posted By jpk91rs

In my opinion, you need to go ported to go really...

In my opinion, you need to go ported to go really low. It requires less power and will get lower. My 10" L7 Solobaric is in a ProBox SuperBass rectangular ported enclosure with 1100 RMS and it will...
Forum: Camaros for Sale
11-25-2006, 03:31 PM
Replies: 38
Views: 2,264
Posted By jpk91rs

I am in Jacksonville. Just south of Tyler. Send...

I am in Jacksonville. Just south of Tyler. Send me some photos of this car also. I am looking to pick up another car.
Forum: Car Audio
10-22-2004, 03:43 PM
Replies: 29
Views: 10,582
Posted By jpk91rs

I concur with the one sub bandwagon also. I have...

I concur with the one sub bandwagon also. I have 1 Solobaric 10" in a ProBox Super Bass ported box and 1100 w RMS @ 1 ohm and that sucker will make your head hurt and get as low as you want. One sub...
Forum: Aftermarket Product Review
06-01-2004, 02:19 PM
Replies: 736
Views: 59,228
Posted By jpk91rs

Put me on the list for a definate cover and stud...

Put me on the list for a definate cover and stud kit.
Forum: Suspension and Chassis
05-19-2004, 12:21 PM
Replies: 4
Views: 415
Posted By jpk91rs

There is a chunk of foam that covers the shock...

There is a chunk of foam that covers the shock stud and nut. It is right where the rear deck drops off behind the seat.
Forum: South Central Region
05-06-2004, 12:23 PM
Replies: 29
Views: 776
Posted By jpk91rs

Count me in. I goter done.

Count me in. I goter done.
Forum: Body
04-21-2004, 02:57 PM
Replies: 15
Views: 881
Posted By jpk91rs

Hawks and Third Gen Resource have the rocker...

Hawks and Third Gen Resource have the rocker emblems. They even have the new ones with the carbon fiber look.
Forum: Tech / General Engine
04-15-2004, 08:48 AM
Replies: 8
Views: 652
Posted By jpk91rs

WHat they said!!!!!!!!!:thumbsup:

WHat they said!!!!!!!!!:thumbsup:
Forum: Tech / General Engine
04-15-2004, 08:23 AM
Replies: 22
Views: 6,244
Posted By jpk91rs

I have run both a Holley Strip Dominator and a...

I have run both a Holley Strip Dominator and a Victor Jr on a oval track 355 dirt car. The Victor Jr won hands down. That is the only time I have run 2 intakes on the same motor for comparison.
Forum: Car Audio
04-13-2004, 02:21 PM
Replies: 15
Views: 629
Posted By jpk91rs

My setup incorporates a Solobaric L510" w/ 2 ohm...

My setup incorporates a Solobaric L510" w/ 2 ohm DVC, so it is running at 1 ohm woofer in a Super Bass Ported Pro Box. The amp I am using is a Memphis Baby Bell 5 channel amp. It puts out 55w rms x 4...
Forum: Car Audio
04-13-2004, 02:12 PM
Replies: 24
Views: 795
Posted By jpk91rs

Well, my setup uses the stock speaker locations...

Well, my setup uses the stock speaker locations for 6x9's and 4x6's and a single solobaric L5 10" sub in the back well. My system sounds very awesome. It is definately the quality of the components...
Forum: Tech / General Engine
04-05-2004, 04:25 PM
Replies: 40
Views: 1,560
Posted By jpk91rs

Go for it. It is something different. It should...

Go for it. It is something different. It should make fairly decent power. Not 355 or 383 power, but good power.
Forum: TBI
03-24-2004, 10:09 AM
Replies: 7
Views: 4,369
Posted By jpk91rs

I have bought the same kit twice and it has...

I have bought the same kit twice and it has worked both times. It is the right kit.
Forum: Tech / General Engine
03-18-2004, 02:15 PM
Replies: 6
Views: 459
Posted By jpk91rs

With .480 lift you won't have a problem. Just...

With .480 lift you won't have a problem. Just bolt 'em on and go.
Forum: Body
03-16-2004, 04:54 PM
Replies: 9
Views: 783
Posted By jpk91rs

gm restoration parts or gm parts direct for the...

gm restoration parts or gm parts direct for the t-top weatherstripping. I bought soffseal for the rear hatch and the door weatherstripping. I was happy with the prices and the quality and fit of the...
Forum: Tech / General Engine
03-08-2004, 01:11 PM
Replies: 46
Views: 1,503
Posted By jpk91rs

BTW, I have seen a lockup convertor installed on...

BTW, I have seen a lockup convertor installed on a non lockup 700R4 and it would lock up intermittently and stall the vehicle. The fluid could be routed to the lockup clutch in the convertor at any...
Forum: Tech / General Engine
03-08-2004, 01:08 PM
Replies: 46
Views: 1,503
Posted By jpk91rs

Hookup a vacuum gauge to that carb and tune for...

Hookup a vacuum gauge to that carb and tune for highest vacuum reading.
Forum: Tech / General Engine
03-08-2004, 12:57 PM
Replies: 17
Views: 596
Posted By jpk91rs

Just go easy and try it. Listen to the motor....

Just go easy and try it. Listen to the motor. Don't start by adding 600 or 700 rpms to your shift points, try 100 or 150 rpms and increase gradually. When the motor lays down you will know. Then use...
Forum: Tech / General Engine
03-08-2004, 12:52 PM
Replies: 17
Views: 596
Posted By jpk91rs

If your motor has been built to handle the stress...

If your motor has been built to handle the stress of higher rpm's they by all means experiment changing shift points. Just listen to your motor, it will tell you when it is unhappy.
Forum: Electronics
03-03-2004, 04:41 PM
Replies: 9
Views: 2,230
Posted By jpk91rs

Mine did not want to come out either. I had to...

Mine did not want to come out either. I had to pull some extra slack for the wires on mine (91 RS) and then the switch came out, but I suppose those are the vats wires.
Forum: Body
03-03-2004, 04:06 PM
Replies: 36
Views: 13,825
Posted By jpk91rs

I have a Harwood cowl hood on my 72 PU. I will...

I have a Harwood cowl hood on my 72 PU. I will never own another one. I will just add 50 horsepower to makeup the speed. The outer and innner sections have started coming apart, (debonding), and as...
Forum: Body
03-03-2004, 04:02 PM
Replies: 8
Views: 455
Posted By jpk91rs

THe red in my car was the brighter red. It is a...

THe red in my car was the brighter red. It is a 91 RS if that helps, but I don't know what color it is for sure. WHere are you located? You can have them for the price of getting them to you. I was...
Forum: Body
03-03-2004, 11:50 AM
Replies: 8
Views: 455
Posted By jpk91rs

I have a set in red. Seatbelts and all. Changed...

I have a set in red. Seatbelts and all. Changed my interior color to gray.
Forum: Car Audio
02-22-2004, 12:33 PM
Replies: 3
Views: 476
Posted By jpk91rs

Got it hooked up yesterday and bumped it to some...

Got it hooked up yesterday and bumped it to some of my favorite music. I can honestly say that I am extremely impressed and pleased. Who knew that 1 Solobaric 10" in a ported box with 400w @ 1 ohm...
Forum: Tech / General Engine
02-20-2004, 11:06 AM
Replies: 17
Views: 862
Posted By jpk91rs

How can you seal a fuel system?

How can you seal a fuel system?
Forum: Tech / General Engine
02-19-2004, 03:03 PM
Replies: 17
Views: 862
Posted By jpk91rs

Yes this is correct. Methanol runs just about...

Yes this is correct. Methanol runs just about double the volume of gasoline so you must have a massive fuel system. Also, methanol causes condensation, condensation is water, water and methanol do...
Forum: Car Audio
02-19-2004, 09:07 AM
Replies: 1,332
Important/Useful : Your Top 5 Tunes
Views: 110,326
Posted By jpk91rs

Here it goes with my top 5: 5. For Those...

Here it goes with my top 5:

5. For Those About to Rock...We Salute You!---AC/DC

4. In Da Club---50Cent

3. When Daddy Let Me Drive---Alan Jackson

2. Someday---Sloth
Forum: Car Audio
02-15-2004, 07:16 AM
Replies: 28
Views: 2,585
Posted By jpk91rs

Anyone got any press on Interfire amps or...

Anyone got any press on Interfire amps or Memphis. I guess alot of these things are regional. Different suppliers and different regions of the country that they serve.
Forum: Car Audio
02-15-2004, 07:10 AM
Replies: 3
Views: 476
Posted By jpk91rs

New system

I have just finished ordering all of my new stereo stuff. Here it goes: 2 Memphis 4x6 speakers with the aimable tweeter
2 Interfire 6x9 3 way speakers
1 Solobaric L5 10"...
Forum: Body
02-15-2004, 06:57 AM
Replies: 11
Views: 3,452
Posted By jpk91rs

Medium Spiral Gray Metallic

I just got my car back from my paint guy last Sunday. My wife and I chose a 2004 Corvette color called Medium Spiral Gray Metallic. This color should have come on 3rd gen cars from the factory. I am...
Forum: Body
02-15-2004, 06:51 AM
Replies: 36
Views: 13,825
Posted By jpk91rs

I have always been told that you should put an...

I have always been told that you should put an unpainted fiberglass hood on your car for awhile before you paint it so it can cure and weather. I am not sure of the source, but I do remember the tip.
Forum: Body
02-15-2004, 06:48 AM
Replies: 12
Views: 749
Posted By jpk91rs

I just ordered a new steel cowl hood for my 91 RS...

I just ordered a new steel cowl hood for my 91 RS from GM Restoration Parts aka. Goodmark. It was missing the entire inner reinforcing structure. It was just the outer shell. THen they gave my...
Forum: Body
02-12-2004, 02:25 PM
Replies: 11
Views: 4,323
Posted By jpk91rs

You can have the car straightened, but you have...

You can have the car straightened, but you have to decide what amount of money it is worth to you. I spent $1000 to have my sub-frame straightened and $150 for a parts car for the new k-member abd...
Forum: Tech / General Engine
01-29-2004, 09:50 AM
Replies: 5
Views: 509
Posted By jpk91rs

I was told it was internally balanced on the...

I was told it was internally balanced on the front and externally balanced on the rear of the one piece cranks. Is this accurate?
Forum: Tech / General Engine
01-27-2004, 02:27 PM
Replies: 21
Views: 1,339
Posted By jpk91rs

I like the new rubber gaskets. I used to run the...

I like the new rubber gaskets. I used to run the cork ones, but they start hardening when they get old and hot. They are also harder to clean off of the valve covers. The rubber ones seem to remain...
Showing results 1 to 50 of 238
 
Page 1 of 5
1
2
3
4
5


 
Forum Jump


All times are GMT -5. The time now is 06:58 AM.